73 is still almost 30 degrees under the thermal shutdown. so that is
relatively safe.
On Thu, Jul 16, 2020 at 4:50 PM Michael via PLUG-discuss <
plug-discuss@lists.phxlinux.org> wrote:
> there is a fan on it and it maxes at 73 with the blue kitty in glmark2
> but usually stays below 68
>
> On Thu, Jul 16, 2020 at 5:48 PM Brian Cluff via PLUG-discuss
>
> <plug-discuss@lists.phxlinux.org> wrote:
> >
> > Hows the temperature of your video card? Does it have a fan on it?
> >
> > Brian
> >
> > On 7/16/20 1:41 PM, Michael via PLUG-discuss wrote:
> >
> >
> > Might the problem still be the he
> >
> > On Thu, Jul 16, 2020 at 4:37 PM Stephen Partington via PLUG-discuss <
> plug-discuss@lists.phxlinux.org> wrote:
> >>
> >> 68C under load is good. 80C+ idle is bad.
> >>
> >>
> >> On Thu, Jul 16, 2020 at 12:35 PM Michael via PLUG-discuss <
> plug-discuss@lists.phxlinux.org> wrote:
> >>>
> >>> lets get back to heat... last time I was running glx (with the horse
> >>> and various other pictures) and watch, and stress ng the temp was like
> >>> 68. I don't think that is too bad.
> >>>
> >>> On Thu, Jul 16, 2020 at 3:19 PM Brian Cluff via PLUG-discuss
> >>> <plug-discuss@lists.phxlinux.org> wrote:
> >>> >
> >>> > Looks like your drive probably isn't the problem.
> >>> >
> >>> > Brian Cluff
> >>> >
> >>> > On 7/16/20 11:54 AM, Michael via PLUG-discuss wrote:
> >>> > > On Thu, Jul 16, 2020 at 3:37 AM Brian Cluff via PLUG-discuss
> >>> > > <plug-discuss@lists.phxlinux.org> wrote:
> >>> > >> Also check the health of your hard drive with smartctl. I've hard
> >>> > >> systems freeze on me because my hard drive was dying that then
> appear to
> >>> > >> work again for a while after a reboot. Basically your drive
> starts
> >>> > >> throwing errors and eventually the system remounts it as read
> only and
> >>> > >> your system eventually freaks out and freezes because it can't
> write to
> >>> > >> the drive anymore.
> >>> > > I sure hope this is the problem. It'll give me an excuse to put an
> ssd
> >>> > > in the machine.
> >>> > > This is from live media boot. I'll see if I can freeze the system
> >>> > > again.... it did when I tried it before but it hasn't frozen for a
> >>> > > couple of days now.
> >>> > > sudo smartctl --all /dev/sda
> >>> > > smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-26-generic]
> (local build)
> >>> > > Copyright (C) 2002-19, Bruce Allen, Christian Franke,
> www.smartmontools.org
> >>> > >
> >>> > > === START OF INFORMATION SECTION ===
> >>> > > Model Family: Western Digital Caviar Blue (SATA)
> >>> > > Device Model: WDC WD3200AAKS-75L9A0
> >>> > > Serial Number: WD-WMAV2S110171
> >>> > > LU WWN Device Id: 5 0014ee 057775228
> >>> > > Firmware Version: 02.03E02
> >>> > > User Capacity: 320,072,933,376 bytes [320 GB]
> >>> > > Sector Size: 512 bytes logical/physical
> >>> > > Device is: In smartctl database [for details use: -P show]
> >>> > > ATA Version is: ATA8-ACS (minor revision not indicated)
> >>> > > SATA Version is: SATA 2.5, 3.0 Gb/s
> >>> > > Local Time is: Thu Jul 16 18:33:20 2020 UTC
> >>> > > SMART support is: Available - device has SMART capability.
> >>> > > SMART support is: Enabled
> >>> > >
> >>> > > === START OF READ SMART DATA SECTION ===
> >>> > > SMART overall-health self-assessment test result: PASSED
> >>> > >
> >>> > > General SMART Values:
> >>> > > Offline data collection status: (0x84) Offline data collection
> activity
> >>> > > was suspended by an interrupting command from
> host.
> >>> > > Auto Offline Data Collection: Enabled.
> >>> > > Self-test execution status: ( 0) The previous self-test
> >>> > > routine completed
> >>> > > without error or no self-test has ever
> >>> > > been run.
> >>> > > Total time to complete Offline
> >>> > > data collection: ( 6000) seconds.
> >>> > > Offline data collection
> >>> > > capabilities: (0x7b) SMART execute Offline immediate.
> >>> > > Auto Offline data collection on/off support.
> >>> > > Suspend Offline collection upon new
> >>> > > command.
> >>> > > Offline surface scan supported.
> >>> > > Self-test supported.
> >>> > > Conveyance Self-test supported.
> >>> > > Selective Self-test supported.
> >>> > > SMART capabilities: (0x0003) Saves SMART data before
> entering
> >>> > > power-saving mode.
> >>> > > Supports SMART auto save timer.
> >>> > > Error logging capability: (0x01) Error logging supported.
> >>> > > General Purpose Logging supported.
> >>> > > Short self-test routine
> >>> > > recommended polling time: ( 2) minutes.
> >>> > > Extended self-test routine
> >>> > > recommended polling time: ( 73) minutes.
> >>> > > Conveyance self-test routine
> >>> > > recommended polling time: ( 5) minutes.
> >>> > > SCT capabilities: (0x3037) SCT Status supported.
> >>> > > SCT Feature Control supported.
> >>> > > SCT Data Table supported.
> >>> > >
> >>> > > SMART Attributes Data Structure revision number: 16
> >>> > > Vendor Specific SMART Attributes with Thresholds:
> >>> > > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
> >>> > > UPDATED WHEN_FAILED RAW_VALUE
> >>> > > 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail
> >>> > > Always - 0
> >>> > > 3 Spin_Up_Time 0x0027 138 133 021 Pre-fail
> >>> > > Always - 4075
> >>> > > 4 Start_Stop_Count 0x0032 089 089 000 Old_age
> >>> > > Always - 11090
> >>> > > 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail
> >>> > > Always - 0
> >>> > > 7 Seek_Error_Rate 0x002e 100 253 000 Old_age
> >>> > > Always - 0
> >>> > > 9 Power_On_Hours 0x0032 019 019 000 Old_age
> >>> > > Always - 59593
> >>> > > 10 Spin_Retry_Count 0x0032 100 100 000 Old_age
> >>> > > Always - 0
> >>> > > 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age
> >>> > > Always - 0
> >>> > > 12 Power_Cycle_Count 0x0032 098 098 000 Old_age
> >>> > > Always - 2282
> >>> > > 192 Power-Off_Retract_Count 0x0032 199 199 000 Old_age
> >>> > > Always - 1044
> >>> > > 193 Load_Cycle_Count 0x0032 197 197 000 Old_age
> >>> > > Always - 11090
> >>> > > 194 Temperature_Celsius 0x0022 105 080 000 Old_age
> >>> > > Always - 38
> >>> > > 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age
> >>> > > Always - 0
> >>> > > 197 Current_Pending_Sector 0x0032 200 200 000 Old_age
> >>> > > Always - 0
> >>> > > 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age
> >>> > > Offline - 0
> >>> > > 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age
> >>> > > Always - 0
> >>> > > 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age
> >>> > > Offline - 0
> >>> > > 240 Head_Flying_Hours 0x0032 024 024 000 Old_age
> >>> > > Always - 55990
> >>> > > 241 Total_LBAs_Written 0x0032 200 200 000 Old_age
> >>> > > Always - 78243499218
> >>> > > 242 Total_LBAs_Read 0x0032 200 200 000 Old_age
> >>> > > Always - 174621575474
> >>> > >
> >>> > > SMART Error Log Version: 1
> >>> > > No Errors Logged
> >>> > >
> >>> > > SMART Self-test log structure revision number 1
> >>> > > Num Test_Description Status Remaining
> >>> > > LifeTime(hours) LBA_of_first_error
> >>> > > # 1 Short offline Completed without error 00%
> 14352 -
> >>> > > # 2 Short offline Completed without error 00%
> 0 -
> >>> > >
> >>> > > SMART Selective self-test log data structure revision number 1
> >>> > > SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
> >>> > > 1 0 0 Not_testing
> >>> > > 2 0 0 Not_testing
> >>> > > 3 0 0 Not_testing
> >>> > > 4 0 0 Not_testing
> >>> > > 5 0 0 Not_testing
> >>> > > Selective self-test flags (0x0):
> >>> > > After scanning selected spans, do NOT read-scan remainder of
> disk.
> >>> > > If Selective self-test is pending on power-up, resume after 0
> minute delay.
> >>> > >
> >>> > > Well, I am running glmark2, watch, and stress-ng for about (one
> round
> >>> > > of glmark2) with no freeze. all from live media
> >>> > > --
> >>> > > :-)~MIKE~(-:
> >>> > > ---------------------------------------------------
> >>> > > PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org
> >>> > > To subscribe, unsubscribe, or to change your mail settings:
> >>> > > https://lists.phxlinux.org/mailman/listinfo/plug-discuss
> >>> >
> >>> > ---------------------------------------------------
> >>> > PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org
> >>> > To subscribe, unsubscribe, or to change your mail settings:
> >>> > https://lists.phxlinux.org/mailman/listinfo/plug-discuss
> >>>
> >>>
> >>>
> >>> --
> >>> :-)~MIKE~(-:
> >>> ---------------------------------------------------
> >>> PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org
> >>> To subscribe, unsubscribe, or to change your mail settings:
> >>> https://lists.phxlinux.org/mailman/listinfo/plug-discuss
> >>
> >>
> >>
> >> --
> >> A mouse trap, placed on top of your alarm clock, will prevent you from
> rolling over and going back to sleep after you hit the snooze button.
> >>
> >> Stephen
> >>
> >> ---------------------------------------------------
> >> PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org
> >> To subscribe, unsubscribe, or to change your mail settings:
> >> https://lists.phxlinux.org/mailman/listinfo/plug-discuss
> >
> > --
> > :-)~MIKE~(-:
> >
> > ---------------------------------------------------
> > PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org
> > To subscribe, unsubscribe, or to change your mail settings:
> > https://lists.phxlinux.org/mailman/listinfo/plug-discuss
> >
> >
> > ---------------------------------------------------
> > PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org
> > To subscribe, unsubscribe, or to change your mail settings:
> > https://lists.phxlinux.org/mailman/listinfo/plug-discuss
>
>
>
> --
> :-)~MIKE~(-:
> ---------------------------------------------------
> PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org
> To subscribe, unsubscribe, or to change your mail settings:
> https://lists.phxlinux.org/mailman/listinfo/plug-discuss
--
A mouse trap, placed on top of your alarm clock, will prevent you from
rolling over and going back to sleep after you hit the snooze button.
Stephen
---------------------------------------------------
PLUG-discuss mailing list -
PLUG-discuss@lists.phxlinux.org
To subscribe, unsubscribe, or to change your mail settings:
https://lists.phxlinux.org/mailman/listinfo/plug-discuss
(text/plain)