Boot messages when booting into single user mode
Configuring network interfaces...
r8169 0000:01:09.0: eth1:link down
r8169 0000:01:09.0: eth1:link down
ADDRCONF(NETDEV_UP): eth1: link is not ready
r8169 0000:01:09.0: eth1:link ready
ADDRCONF(NETDEV_UP): eth1: link becomes ready
and then it hangs.
Thanks for any suggestions.
Mark
On Sun, Jan 27, 2013 at 5:07 PM, Mark Phillips
<
mark@phillipsmarketing.biz>wrote:
> 1. I installed a new nic, an asus NX1101, and went into the bios and
> disabled the on board network interface controller. The system booted, but
> the network was not working.
>
> 2. I then edited the /etc/network/interfaces file and changed eth0 to eth1
> for the new nic. I then ran ifup eth1, and the network came up. I could
> ping google.com and ssh to the box.
>
> 3. I rebooted the machine, and the boot process again stopped at
> Configuring the network. I rebooted again to check if the bios had been
> changed, and the bios still says that the on board network interface
> controller is disabled.
>
> So now the new nic is enabled, but the system still hangs at trying to
> configure the network.
>
> Anyone have any ideas?
>
> Thanks,
>
> Mark
>
>
>
> On Sun, Jan 27, 2013 at 12:04 PM, Matt Graham <danceswithcrows@usa.net>wrote:
>
>> From: Mark Phillips <mark@phillipsmarketing.biz>
>> > There was an ATI Rage 128 video card in the system, and the the newer
>> > Debians do not have the radeon drivers.
>>
>> That shouldn't have caused any problems. Rage 128 cards use the r128 X
>> module, not the radeon one. Why is Debian not including the radeon
>> modules?
>> That just seems weird and counterproductive, since so many machines out
>> there
>> have video cards driven by that module. And if it's headless, it should
>> probably be starting up without X, in a VGA text console or vesafb, so
>> that
>> the video card is completely irrelevant.
>>
>> > However, the system hangs when trying to start network services.
>> > [10.184481] e1000: eth0 NIC Link is UP 1000 Mbps Full Duplex, Flow
>> > Control: RX/TX
>> > [10.187930] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
>> >
>> > Then nothing is printed out and the system does not respond.
>> > The card is the internal NIC - I don't have any extra cards in the
>> > machine.
>>
>> Take a random PCI NIC you have lying around. Put that NIC in the
>> machine. Go
>> into the machine's BIOS Setup and disable the internal NIC. If you do
>> that,
>> and the thing boots normally, then the machine's internal NIC is hosed.
>> BTDT.
>> NIC failure *can* happen, it's just sort of rare since there aren't any
>> moving parts.
>>
>> Or the new kernel has some sort of weird bug with its e1000 module.
>> Distro
>> kernels seem to have more weird bugs than vanilla kernels, for some
>> reason.
>> You could test this by booting with the rescue system's option for "no
>> network", then if it comes up, and you modprobe e1000 and it immediately
>> locks
>> up, that may be the problem.
>>
>> --
>> Matt G / Dances With Crows
>> The Crow202 Blog: http://crow202.org/wordpress/
>> There is no Darkness in Eternity/But only Light too dim for us to see
>>
>> ---------------------------------------------------
>> PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org
>> To subscribe, unsubscribe, or to change your mail settings:
>> http://lists.phxlinux.org/mailman/listinfo/plug-discuss
>>
>
>
---------------------------------------------------
PLUG-discuss mailing list -
PLUG-discuss@lists.phxlinux.org
To subscribe, unsubscribe, or to change your mail settings:
http://lists.phxlinux.org/mailman/listinfo/plug-discuss
(text/plain)