Look up rfc1918, it details the private networks. Three major classes
of private ipv4 as Kevin listed. In large networks, you will tend to
see all 3 uses, typically with physical or security differences in them.
They usually only touch in internal network peering relationships with
a routing protocol.
Don't mix and match lightly (or do, but look up gns3 first), and learn
CIDR subnet/supernet masking. Don't go by class a/b/c/d anymore, it's
all cidr now, and with ipv6 it only gets worse.
-mb
On 03/08/2012 10:46 AM, Kevin Fries wrote:
> Mike,
>
> Just for your information, there is also a third lesser known range
> 172.[16-31].x.y
>
> Each of the three ranges are available for private use, and are illegal
> on the Internet. Which you use is completely up to you and is generally
> based upon your own individual needs.
>
> If you take the first part of any address, and represent it in binary,
> it will tell you the address "class".
>
> 0.... -> Class A address
> 10... -> Class B address
> 110.. -> Class C address
> 1110. -> Class D address
> 11110 -> Class E address
>
> 10 -> 0000 1010 -> Class A - Default mask is 255.0.0.0 - CIDR /8
> 172 -> 1010 1100 -> Class B - Default mask is 255.255.0.0 - CIDR /16
> 192 -> 1100 0000 -> Class C - Default mask is 255.255.255.0 - CIDR /24
>
> Class D was reserved for multi-cast addresses. Most of these you will
> see in the 224.x.y.z range
>
> 224 -> 1110 0000 -> Class D - Default mask is 255.255.255.255 - CIDR /32
>
> Class E was reserved, but never used, and never will be now that IPv6 is
> here.
>
> Using a class A address reserves 8 bits for the network address (i.e.
> 10) and 24 bits for the hosts, which leaves you with 2^24 or 16,777,216
> hosts - 2 (network broadcast, and network addresses)
>
> Using a class B address reserves 16 bits for the network (i.e. 172.16)
> and 16 bits for the hosts, which leaves you with 2^16 or 8,65,536 hosts
> - 2 (network broadcast, and network address)
>
> Using a class C address reserves 24 bits for the network (i.e.
> 192.168.1) and 8 bits for the host, which leaves you with 2^8 or 256 -
> the same 2 addresses.
>
> Your broadcast address is where all bits in the host part are 1, and
> your network address is where all host bits are 0.
>
> I hope this helps you understand the difference between addresses, and
> helps you pick the right one for your needs.
>
> Kevin Fries
>
>
>
> On Thu, 2012-03-08 at 10:18 -0700, Michael Havens wrote:
>> What is the difference between the 192.168.x.y and the 10.x.y.z range?
>> They are both the private network ranges but why would one decide to
>> use one but not the other?
>>
>> --
>> :-)~MIKE~(-:
>> ---------------------------------------------------
>> PLUG-discuss mailing list - PLUG-discuss@lists.plug.phoenix.az.us
>> To subscribe, unsubscribe, or to change your mail settings:
>> http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss
>
>
> ---------------------------------------------------
> PLUG-discuss mailing list - PLUG-discuss@lists.plug.phoenix.az.us
> To subscribe, unsubscribe, or to change your mail settings:
> http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss
>
>
---------------------------------------------------
PLUG-discuss mailing list -
PLUG-discuss@lists.plug.phoenix.az.us
To subscribe, unsubscribe, or to change your mail settings:
http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss
(text/plain)