RE: fix lockup issue left with one core

Does it show one or two CPUs at bogomips 4790?

I notice on my mint system, in dmesg:

[    0.180737] Brought up 2 CPUs
[    0.180739] smpboot: Total of 2 processors activated (12801.34 BogoMIPS)

So do you see 2 or 1 there in your version? (Assuming you get a similar message)


-----Original Message-----
From: plug-discuss-bounces@lists.phxlinux.org on behalf of Derek Trotter
Sent: Tue 8/13/2013 8:13 PM
To: Main PLUG discussion list
Subject: Re: fix lockup issue left with one core

Update. I tried encoding that video again, but without the noapic and
nolapic options. Handbrake was encoding the video at between 35 and 40
frames per second. When I rebooted and tried again with the noapic and
noalpic options enabled, Handbrake was encoding the same video with the
same settings at 17 to 20 frames a second. So is this something unique
to Handbrake or is there something else going on?

Derek

First I checked /proc/cpuinfo which had 4790.8 as the value for bogomips
with noapic and nolapic in the grub2 config. I removed these options
and rebooted. This time I got 4791.43. So I'm guessing that if I
lost anything, it's not enough to matter. Am I right?

Thanks

On 08/13/2013 02:56 PM, Carruth, Rusty wrote:
>
> Compare the bogomips of the dual-core boot and the single-core boot.
>
> Â
>
> If the bogomips of the single-core is 2x the bogo of the dual
> core, then you’ve not lost anything – you are simply letting Linux
> control the sharing of the CPU instead of the CPU.
>
> Â
>
> (at least for the stupid hyperthreading stuff, all hyperthreading did
> was give you two CPUs running at half the clock speed of the CPU…Â
> Helped Windows users since Windows did such a bad job of time slicing
> on a single CPU…)
>
> Â
>
> Â
>
> *From:*plug-discuss-bounces@lists.phxlinux.org
> [mailto:plug-discuss-bounces@lists.phxlinux.org] *On Behalf Of *Derek
> Trotter
> *Sent:* Tuesday, August 13, 2013 2:53 PM
> *To:* Main PLUG discussion list
> *Subject:* fix lockup issue left with one core
>
> Â
>
> So far this beast has behaved itself for 3 days. Today I handbrake on
> a tv show episode I have on dvd. It's a 30 minute show and Handbrake
> normally takes about 20 minutes to encode a 30 minute show. This
> time I noticed the estimation of how long it would take hovered around
> 45 minutes. I then opened top and pressed 1 once it started. It
> showed only cpu0. Shouldn't cpu1 also be there? I looked around
> online and found that using the noapic option in grub only allows one
> core of a multi core processor to run. Is there any way to enable
> apic and lapic if necessary without it causing my machine to lock up
> again?
>
> Thanks
>
> --
> "I get my copy of the daily paper, look at the obituaries page, and if I’m not there, I carry on as usual."
> Â
> Patrick Moore
>
>
> ---------------------------------------------------
> PLUG-discuss mailing list -PLUG-discuss@lists.phxlinux.org
> To subscribe, unsubscribe, or to change your mail settings:
> http://lists.phxlinux.org/mailman/listinfo/plug-discuss

--
"I get my copy of the daily paper, look at the obituaries page, and if I’m not there, I carry on as usual."

Patrick Moore


---------------------------------------------------
PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org
To subscribe, unsubscribe, or to change your mail settings:
http://lists.phxlinux.org/mailman/listinfo/plug-discuss