RE: Problem compiling Broadcom 440x drivers for open Solaris

There is no "make" in the working directory. I did check that, and even if I
didn't running gcc and suncc from their full bin paths would have accounted
for it. :( Also the files look fine under VIM; at least to me it looks fine.
I downloaded the tar.gz file from the server using Ubuntu and copied using a
flash drive but untared/ziped on the sun box so their should be no windows
contaminates on my end.

I had actually gone down that road of though already, but thank you for the
suggestions. Some times the most obvious issue is the one that takes you
days to find.

-----Original Message-----
From: plug-discuss-bounces@lists.plug.phoenix.az.us
[mailto:plug-discuss-bounces@lists.plug.phoenix.az.us] On Behalf Of Bob
Elzer
Sent: Sunday, April 05, 2009 3:50 PM
To: 'Main PLUG discussion list'
Subject: RE: Problem compiling Broadcom 440x drivers for open Solaris

Make sure (lol) that you don't have a file in the current directory named
"make"

Also sometime the files may have cr/lf in them which cause problems, this
happens if the file came from a dos/win environment.

check your makefile



-----Original Message-----
From: plug-discuss-bounces@lists.plug.phoenix.az.us
[mailto:plug-discuss-bounces@lists.plug.phoenix.az.us] On Behalf Of Bryan
O'Neal
Sent: Sunday, April 05, 2009 2:49 PM
To: 'Main PLUG discussion list'
Subject: Problem compiling Broadcom 440x drivers for open Solaris

I installed Open Solaris on my Dell Inspiron 6000 notebook, however the
Broadcom 440x integrated nic card is not supported.
I found the following link
http://www.sun.com/bigadmin/hcl/data/components/details/363.html
<http://www.sun.com/bigadmin/hcl/data/components/details/363.html> which
leads me to a driver pack, which provides a set of instructions that
basically boiled down to #make #make install however make does not compile
anything.
make reports Fatal error: No arguments to build. make Makefile reports
Makefile is uptodate. And of course, since I can not make I am not surprised
when make install reports Don't know how to make target 'install'

I have gotten so used to 
    #./config <arguments> 
    #make
    #make install
over the last decade that I have lost the trouble shooting talent for this
sort of thing. I have tried with gcc and suncc but I get the same issue both
times. There is no actual configure script since the make files come predone
for a dozen different platforms/os/compiler combos that are supported; you
just simlink to the rite one and go.

Suggestions?

Bryan O'Neal
O'Neal & Associates
Phone: (602) 295-4356
Fax:     (602) 795-6050
E-Mail: Bryan.ONeal@TheONealAndAssociates.com 

Blogger <http://twitter.com/BryanONeal> Twitter
<http://mlwtech.blogspot.com/> Linkedin
<http://www.linkedin.com/in/thebryanoneal>






---------------------------------------------------
PLUG-discuss mailing list - PLUG-discuss@lists.plug.phoenix.az.us
To subscribe, unsubscribe, or to change your mail settings:
http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss

---------------------------------------------------
PLUG-discuss mailing list - PLUG-discuss@lists.plug.phoenix.az.us
To subscribe, unsubscribe, or to change your mail settings:
http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss

---------------------------------------------------
PLUG-discuss mailing list - PLUG-discuss@lists.plug.phoenix.az.us
To subscribe, unsubscribe, or to change your mail settings:
http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss