RE: How to connect four edi devices?

In your bios, did you set the IDE devices or are they set to auto
detect? What your bios is reporting looks like a standard manufactures
setting. Try setting all four devices to auto detect.

-----Original Message-----
From: plug-discuss-bounces@lists.plug.phoenix.az.us
[mailto:plug-discuss-bounces@lists.plug.phoenix.az.us] On Behalf Of
Josef Lowder
Sent: Saturday, April 28, 2007 4:15 PM
To: Main PLUG discussion list
Subject: Re: How to connect four edi devices?

.
The following is additional info pertaining to the subject problem.
> > What is the correct way to connect four edi devices?
> > I have an older computer that has a 20-gig hard drive, an older cd
> > burner and a recent dvd player and I want to add an older 6.4-gig
> > hard drive.

Now, having the four drives connected as previously described, when I
try to boot up, I see the following screen messages:

AMD Duron 1100 Mhz
Pri Master VAM51J Maxtor 2F020Lo
     Ultra DMA Mode 5 - S.M.A.R.T. Capable but disabled 

(I have also tried setting SMART as enabled.)

AMBIOS Setup shows this:

Prim Master - User 20848 MB 
Prim Slave  -  CD-Rom       (But this is not true.)
Sec Master  - Not Installed (But this is not true.)
Sec Slave   - Not Installed (But this is not true.)

The Second HD *is* installed as the primary slave with the IDE cable
connected from IDE-1 on the mother board to the original 20-gig Maxtor
HD at the end of the cable and the 6.4-gig Western Digital HD connected
to the middle of the cable.

Furthermore, the two CD drives (a DVD and a CD-writer) connected from
IDE-2 on the mother board on the same cable.

No matter how I reconfigure bios, I always see the same messages:

Prim Slave Drive - ATAPI incompatible
Press F1 to resume.

But this makes no sense because when I boot up with either WinXP or
Xandros Linux on the two-partition 20-gig HD, from either operating
system, I can read the contents of the 6.4-gig drive.

While I did not make any changes in the boot loader (and I don't know if
it is grub or lilo), after connecting the 6.4-gig HD, the boot loader
added two items to the list of options that were not previously there,
neither of which work. This is what the Xandros boot loader splash
screen shows:

1. Xandros (WinXP used to be the first options) -- Xandros boots fine.
2. Safe Video mode
3. Configure (Expert)
4. Windows XP (it boots fine)
5. Red Hat Linux (This was *not* on the original Xandros boot screen)
... and it does not boot. There was a Red Hat Linux partition on
the 6.4-gig HD that I am trying to use on this system.
6. Linux Mandrake (This also was *not* on the original Xandros boot)
... and it does not work. This is especially strange because
there has never been a Mandrake Linux installation on either HD.

This is a great mystery!

My objective is to reformat the 6.4-gig drive, install PCLinuxOS on it
and triple boot with PCLinuxOS in the first (default) position, XP
second, and Xandros third.

What do I need to do to get the system to boot from any Linux "live" CD?



---------------------------------------------------
PLUG-discuss mailing list - PLUG-discuss@lists.plug.phoenix.az.us
To subscribe, unsubscribe, or to change you mail settings:
http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss
---------------------------------------------------
PLUG-discuss mailing list - PLUG-discuss@lists.plug.phoenix.az.us
To subscribe, unsubscribe, or to change you mail settings:
http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss