I think I found something, but I don't know what it means. While I was in
YaST, I tried to edit the nic card which is recognized as D-Link dfe-530TX+
10/100 Ethernet Adapter Configured as eth0 with DHCP. A Window opens with
this in it: the resolver configuration file(/etc/resolv.conf) has been
temporary modified by dhcpcd. You have 2 options: 1 Modify and 2 Accept. If
you select modify, you will see 3 different IP addresses from Cox Cable. Any
thoughts?
Thanks,
Dale McGarry
-----Original Message-----
From:
plug-discuss-bounces@lists.plug.phoenix.az.us
[
mailto:plug-discuss-bounces@lists.plug.phoenix.az.us] On Behalf Of Joseph
Sinclair
Sent: Saturday, August 06, 2005 8:47 PM
To: Main PLUG discussion list
Subject: Re: SuSE 9.0 Personal internet connection problem
You need to run the YAST2 Network Configuration Control panel. There's an
option there to have it detect your network interfaces and auto-configure
them. You need to run that first, then, if needed, tweak the settings to
match what you actually have.
This is a common problem with YAST, in that it can, essentially, delete
configurations that are in the middle of being updated when a failure
occurs.
Dale McGarry wrote:
> I ran ifup eth0 and got ERROR: No configuration found for ethO. I ran
> ifconfig again and same report as before was displayed.
>
> No problem, I don't know SuSE at all.
>
> Thanks,
>
> Dale McGarry
>
> -----Original Message-----
> From: plug-discuss-bounces@lists.plug.phoenix.az.us
> [mailto:plug-discuss-bounces@lists.plug.phoenix.az.us] On Behalf Of Craig
> White
> Sent: Saturday, August 06, 2005 6:36 PM
> To: Main PLUG discussion list
> Subject: RE: SuSE 9.0 Personal internet connection problem
>
> On Sat, 2005-08-06 at 18:31 -0700, Dale McGarry wrote:
>
>>Sorry about the HTML format.
>>
>>Here is what I see when I ran ifconfig:
>>
>>Link encap: Local Loopback
>>Inet addr: 127.0.00.1 Mask: 255.0.0.0
>>Inet6addr: ::1/128 Scope: Host
>>UP LOOPBACK RUNNING MTU:16436 Metric:1
>>RX packets:50 errors:0 dropped:0 overruns:0 frame:0
>>TX packets:50 errors:0 dropped:0 overruns:0 carrier:0
>>Collisions:0 txqueue:0
>>RX bytes:2608 (2.5 Kb) TX bytes:2608 (205Kb)
>>
>>However, when I ran cat/etc/resolv.conf this what was displayed:
>>bash: cat/etc/resolv.conf: No such file or directory
>>
>>No router, cable goes into external modem (Scientific Atlanta DPC 2100)
>
> and
>
>>runs to PC and, yes I have to power down the modem when I want to switch
>>computers.
>
> ----
> OK - you don't have any ethernet interface active...
>
> try (as root)
>
> ifup eth0
>
> and see what happens (try running 'ifconfig' command again to see if
> interface activates and gets an ip address)
>
> It's likely that YAST has a configuration panel to the network adaptors
> and can turn it on as well...I don't know SuSE well.
>
> Craig
>
> ---------------------------------------------------
> PLUG-discuss mailing list - PLUG-discuss@lists.plug.phoenix.az.us
> To subscribe, unsubscribe, or to change you mail settings:
> http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss
>
> ---------------------------------------------------
> PLUG-discuss mailing list - PLUG-discuss@lists.plug.phoenix.az.us
> To subscribe, unsubscribe, or to change you mail settings:
> http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss
>
---------------------------------------------------
PLUG-discuss mailing list -
PLUG-discuss@lists.plug.phoenix.az.us
To subscribe, unsubscribe, or to change you mail settings:
http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss
---------------------------------------------------
PLUG-discuss mailing list -
PLUG-discuss@lists.plug.phoenix.az.us
To subscribe, unsubscribe, or to change you mail settings:
http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss
(text/plain)