Cisco DoS required CBOS upgrade- Qwest complaint

It's qworst, you expect anything more?

http://www.cisco.com/warp/public/794/675_faq.shtml

Zmodem transfers are rather painful, I'd say look into the password recovery
steps (if you don't know your pw) listed on that page and tftp it. Set the
eth0 ip as it says, enable tftp on the router, and "man tftp".

http://nutsac.org/stuff/c675.2.4.5.bin

-mbutash

-----Original Message-----
From: plug-discuss-admin@lists.plug.phoenix.az.us
[mailto:plug-discuss-admin@lists.plug.phoenix.az.us]On Behalf Of Eric
Richardson
Sent: Monday, June 10, 2002 1:59 PM
To: plug-discuss@lists.plug.phoenix.az.us
Subject: Re: Cisco DoS required CBOS upgrade- Qwest complaint


Patrick Fleming EA wrote:

> I have been in contact with Cisco support as well as customer support
> within Qwest regarding a serious Denial of Service update to the software
> that runs my Cisco 678 router. On 5-23-2002 Cisco released the following
> advisory: http://www.cisco.com/warp/public/707/CBOS-DoS.shtml As
> indicated, I called Qwest- the provider of my modem. The first person I
> talked to transfered me to another department. Without talking to anyone
> at all, just following the prompts provided by the voice mail system, I
> was able to get right back where I originally started, with DSL Tech
> support. This time I was told that they had just received a memo regarding
> the updated software but that he didn't know anything more regarding the
> memo. This was either 5-28 or 5-29. I emailed Cisco, based upon their
> press release to attempt to get the update from them as I was unsuccessful
> with getting anything from Qwest. Their response is the following website:
> http://www.qwest.com/dsl/customerservice/modemsupport.html which as of
> 9:00am 5-31-2002 indicated that they are working on getting the software
> ready for use by their customers. This software has been available since
> 5-23 from Cisco, but since Qwest DSL users purchase their modems from
> Qwest, Cisco indicates that it is Qwest's responsibility to provide the
> upgrades. I would have no problem with that if Qwest fulfilled this
> responsibility with their customers, of which I am only one. I have
> recontacted Cisco in regards to the unavailability of the upgrade on
> Qwest's site and I seem to be in a support loop waiting for a human to
> read my email.
>
> I believe that this deserves the attention of the Corporation Commission
> as it represents a shortfall in the quality of service provided by a
> public utility.
>
>
>
from 5-13-02

Eric Richardson wrote:

Hi,
Is there a way to get the CBOS 2.4.3 for a 675 and install it with Linux
via the terminal port and a com program. I have tried connecting via
modem serial port but I'm not really sure how to do the upgrade. I'm in
routing mode so I don't think I can use the tftp procedure as the router
doesn't have a IP address.

Any help appreciated,



Thanks for the help / encouragement. I wanted to send an update on my
findings.

I didn't know that the .exe format is a zip format - that is
interesting. I found a place on line for the firmware.
http://postyware.dyndns.org/cisco-firmware Note that the images are
different based on the original CBOS version. In my case this was 2.2.0.

I tried to use the tftp program to download the code but had no luck.
I'm using Debian 2.2 so I was able to apt-get tftp. I installed minicom
to communicate to the router but what I did wrong was I did not install
lrzsz which contains the kermit, xyz/modem stuff. I thought perhaps the
option were wrong so I went to look at the man pages for sx (send
xmodem) and it was there so then I knew I was a dummy. I found that the
lrzsz was recommended but not a dependency for minicom.

Finally, after I had the right software but still no luck, I decided to
try zmodem which didn't work and then ymodem which worked. I have no
idea why xmodem didn't work but ymodem did. I upgraded to 2.4.4 and all
seems well. I use FastQ and they are finding that the PPP mode rather
than the routing mode is more stable so eventually they will be moving
customers that direction.

Is anybody using the filtering, NAT, DHCP with cisco and what features
for the Linux firewall. Maybe this is better for another thread.

Eric


________________________________________________
See http://PLUG.phoenix.az.us/navigator-mail.shtml if your mail doesn't
post to the list quickly and you use Netscape to write mail.

PLUG-discuss mailing list - PLUG-discuss@pluglist.mybutt.net
http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss


________________________________________________
See http://PLUG.phoenix.az.us/navigator-mail.shtml if your mail doesn't post
to the list quickly and you use Netscape to write mail.

PLUG-discuss mailing list - PLUG-discuss@lists.plug.phoenix.az.us
http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss