CentOS Networking with V Box

[Michael Torres]

What is your "outside" interface you're bridging to?  Where does the "host"
get it's address from?

I am assuming your refering to my network adapter?  in this case my
wireless adpater and yes, in my VBox config settings,  I am choosing that
adapter

If your familiar with VBox settings, here they are line by line...

Attached To: Bridged Adapter
Name: Killer Wireless-n/a/ac 1525 Wireless Network Adapter
Adapter Type: Intel PRO/1000 MT Desktop (82540EM)
Promiscuous Mode: Deny
MAC address: 080027FFA0AC
Cable Connected: yes


I have verified that the MAC address is the same in my ifcfg-enp0s3 file.



On Tue, Feb 3, 2015 at 11:14 PM, Michael Butash <michael at butash.net> wrote:

>  Sounds like you're binding to the wrong interface for your bridge for
> vbox.  You shouldn't need to put it in promiscuous unless you're intending
> to sniff actually with wireshark or like.
>
> As asked, ifconfig -a would be helpful.
>
> What is your "outside" interface you're bridging to?  Where does the
> "host" get it's address from?
>
> Make sure vbox is binding to "that" interface.
>
> I've not ever had an issue with that occurring unless picking the wrong
> interface on the system on wired.
>
> Ahh, yes on "wired".  Wireless is different - depending on the wireless,
> the router/ap might not let you get another address.  Enterprise (and
> commercial hotspot systems) wifi systems like cisco do things like dhcp
> binding for the host, disallowing you as the cpe device from binding with
> an additional mac address on that session as "bridged".  Your only
> alternative at that point is to use the nat interface for translating you
> out via your acquired host address off an internal interface.
>
> -mb
>
>
> On 02/03/2015 08:07 PM, Michael Torres wrote:
>
>          Hello all,
>
>  I have an problem that  I cannot seem to figure out.....
>
>  I am trying to use "Bridged" networking in Virtual Box to a CentOS 7
> minimum install distro that I want to use for my development server.
>
>  I have used Bridged networking in the past and never had any issues but
> that was with older versions of CentOS
>
>  The issue....  DHCP will not assign a IPv4 address to the server.
>
>  Here is the weird part...  I was at startbucks and actually got it to
> work! (Please, hold the "Just use it at starbucks then" comments..I
> know....)
>
>  Here is the process I used...
>
>  -Installed a fresh CentOS 7 on VBox
>  -While on NAT,  I performed "yum update" so my server was fresh with the
> latest
>  -Disabled SELinux
>  -Disabled the Firewall
>  -Shut down server to reconfigure the adapter to "Bridged"
>  -used adapter type of "Intel Pro 1000 MT Desktop (82540EM)"
>  -set it to "Promiscuous Mode"
>  -restart the server
>
>
>  Again, at Starbucks it assigned a IP address, so this leads me to believe
> that the issue is with a configuration on my router.
>
>  I am not very good at networking, so any help would be appreciated.
>
>  If you need error messages or other output, let me know (and possibly the
> command as I don't know networking that well other than "ifconfig")
>
>
> Mike
>
>
> ---------------------------------------------------
> PLUG-discuss mailing list - PLUG-discuss at lists.phxlinux.org
> To subscribe, unsubscribe, or to change your mail settings:http://lists.phxlinux.org/mailman/listinfo/plug-discuss
>
>
>
> ---------------------------------------------------
> PLUG-discuss mailing list - PLUG-discuss at lists.phxlinux.org
> To subscribe, unsubscribe, or to change your mail settings:
> http://lists.phxlinux.org/mailman/listinfo/plug-discuss
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.phxlinux.org/pipermail/plug-discuss/attachments/20150203/e0f5a7fb/attachment.html>