liksys WRT54G

[Michael Havens]

Lisa, I didn't thank you for the link to the instructions. Thank you  so
much.

:-)~MIKE~(-:

On Wed, Oct 22, 2014 at 1:56 PM, Stephen Partington <cryptworks at gmail.com>
wrote:

> I do not think it is a benefits thing, but subtle variances in the build
> of the router. Look up the specific model/version of your router. backup
> your original firmware and download the stock firmware just to have them
> handy.
>
> from there once you pin down the specific one you need use and stick with
> that.
>
>
>
> On Wed, Oct 22, 2014 at 1:33 PM, Michael Havens <bmike1 at gmail.com> wrote:
>
>> Are these the instructions? It does seem easy! He says we should the 8.09
>> but gives us the link to the 10.03. Should I use the 10.03 or look for the
>> 8,.09? What are the benefits of brcm-47xx over brcm-2.4?
>> Using the Linksys web GUI
>>
>> It is possible to install OpenWrt directly with the Linksys web GUI. If
>> you are initially installing OpenWrt use the Linksys web GUI, this is
>> the easiest way.
>>
>>    - Download the openwrt-wrt54g-squashfs.bin firmware image from the
>>    brcm-2.4 folder to your PC.
>>    - You can find that image at:
>>    http://downloads.openwrt.org/backfire/10.03.1/brcm-2.4/
>>    - Actually the safest version to use would be *8.09*. *Hmmm, it looks
>>    like 10.03.1 is safe but you must use the brcm-2.4 variant like in the link
>>    above*. I am not risking bricking my router for the initial flash, so
>>    I am going with *8.09*.
>>    - Open http://192.168.1.1/Upgrade.asp in your browser or manually go
>>    to http://192.168.1.1 → Administration → Firmware Upgrade
>>    - Upload openwrt-wrt54g-squashfs.bin
>>    - Wait 2 minutes. The router will reboot itself automatically after
>>    the upgrade is complete.
>>    - Your router should now be telnettable at 192.168.1.1. The web
>>    interface luci is also available athttp://192.168.1.1 . Telnet is
>>    disabled and ssh is enabled once a password has been set.
>>    - Type these commands out in telnet/ssh. This is to ensure that tftp
>>    is available, in case your router gets bricked.
>>
>> nvram set boot_wait=on
>> nvram set boot_time=10
>> nvram set wait_time=10 #important for some models
>> nvram commit && reboot
>>
>>
>>    - *You're done!* At this point, you are free to continue using
>>    brcm-2.4. However, if you wish to use brcm47xx, proceed below.
>>    - Download the image openwrt-brcm47xx-squashfs.trx here:
>>    http://downloads.openwrt.org/backfire/10.03.1/brcm47xx/
>>    - Upload using luci at System > Flash Firmware
>>    - *OR*, you can simply ssh into the router,
>>
>> cd /tmp
>> wget http://downloads.openwrt.org/backfire/10.03.1/brcm47xx/openwrt-brcm47xx-squashfs.trx
>> sysupgrade /tmp/openwrt-brcm47xx-squashfs.trx
>>
>>
>>    - Wait for the router to reboot and login! In case you somehow found
>>    out that you can't telnet, then ssh should be possible since your previous
>>    settings before flashing remained (unless you usedsysupgrade -n)
>>    -
>>
>>
>>
>> :-)~MIKE~(-:
>>
>> On Wed, Oct 22, 2014 at 1:07 PM, Stephen Partington <cryptworks at gmail.com
>> > wrote:
>>
>>> I would read through the install, for the wrt its really well known and
>>> as long as you do it over the wire its very simple to update and run the
>>> custom ddwrt. just like loading a normal firmware update.
>>>
>>> On Wed, Oct 22, 2014 at 1:04 PM, Michael Havens <bmike1 at gmail.com>
>>> wrote:
>>>
>>>> I can't reset  to default. I tried the quick method (press reset for 30
>>>> seconds)and the other way (press 30 seconds, while pressing unplug for 30
>>>> seconds and then continue pressing and plug back in and hold 30 more
>>>> seconds). Well, I changed the password to the router and lost wifi
>>>> connectivity and it won't accept the new password.... or the oldone.... but
>>>> I don't need wifi off that router because wifi off of the qwest router
>>>> started working again as soon as I lost connectivity off of the wrt.
>>>>
>>>> Lisa,
>>>> I wish that I could bring it to an installfest because I am so afraid
>>>> of bricking my device; but I live in Cottonwood and work EVERY Saturday.
>>>>
>>>> :-)~MIKE~(-:
>>>>
>>>> On Wed, Oct 22, 2014 at 5:42 AM, Stephen Partington <
>>>> cryptworks at gmail.com> wrote:
>>>>
>>>>> On the plus side you can reset to factory defaults easily without a
>>>>> password.
>>>>>
>>>>>
>>>> ---------------------------------------------------
>>>> PLUG-discuss mailing list - PLUG-discuss at lists.phxlinux.org
>>>> To subscribe, unsubscribe, or to change your mail settings:
>>>> http://lists.phxlinux.org/mailman/listinfo/plug-discuss
>>>>
>>>
>>>
>>>
>>> --
>>> A mouse trap, placed on top of your alarm clock, will prevent you from
>>> rolling over and going back to sleep after you hit the snooze button.
>>>
>>> Stephen
>>>
>>>
>>> ---------------------------------------------------
>>> PLUG-discuss mailing list - PLUG-discuss at lists.phxlinux.org
>>> To subscribe, unsubscribe, or to change your mail settings:
>>> http://lists.phxlinux.org/mailman/listinfo/plug-discuss
>>>
>>
>>
>> ---------------------------------------------------
>> PLUG-discuss mailing list - PLUG-discuss at lists.phxlinux.org
>> To subscribe, unsubscribe, or to change your mail settings:
>> http://lists.phxlinux.org/mailman/listinfo/plug-discuss
>>
>
>
>
> --
> A mouse trap, placed on top of your alarm clock, will prevent you from
> rolling over and going back to sleep after you hit the snooze button.
>
> Stephen
>
>
> ---------------------------------------------------
> PLUG-discuss mailing list - PLUG-discuss at lists.phxlinux.org
> To subscribe, unsubscribe, or to change your mail settings:
> http://lists.phxlinux.org/mailman/listinfo/plug-discuss
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.phxlinux.org/pipermail/plug-discuss/attachments/20141022/7b2a9a1d/attachment.html>