new usb

Mon Nov 6 15:20:50 MST 2006

the parity errors began when I installed a scsi card so I'm very sure it has 
to do with that. In any case the new command (sorry I didn't think  of dmeg 
and tail beig two seperate commands) did produce a new output. The baseline 
and just placing the  the PDA in its cradle gave me the same result as before 
but when I pressed the snync button I got something different.I kept 
increasing the tail variable until the parity error was displayed:  (the 
camera sync output remained the same as yesterday <bad parity error>)

bmike1 at 0[~]$ dmesg|tail -n 80 <after visor sync>
[17210058.664000] hub 1-1:1.0: cannot reset port 1 (err = -71)
[17210058.664000] hub 1-1:1.0: cannot reset port 1 (err = -71)
[17210058.664000] hub 1-1:1.0: Cannot enable port 1.  Maybe the USB cable is 
bad?
[17210058.664000] hub 1-1:1.0: cannot disable port 1 (err = -71)
[17210058.664000] hub 1-1:1.0: cannot reset port 1 (err = -71)
[17210058.664000] hub 1-1:1.0: cannot reset port 1 (err = -71)
[17210058.668000] hub 1-1:1.0: cannot reset port 1 (err = -71)
[17210058.668000] hub 1-1:1.0: cannot reset port 1 (err = -71)
[17210058.668000] hub 1-1:1.0: cannot reset port 1 (err = -71)
[17210058.668000] hub 1-1:1.0: Cannot enable port 1.  Maybe the USB cable is 
bad?
<repeat last 8 lines>
[17210058.676000] hub 1-1:1.0: cannot disable port 1 (err = -71)
[17210058.676000] hub 1-1:1.0: cannot disable port 1 (err = -71)
[17210058.676000] hub 1-1:1.0: hub_port_status failed (err = -71)
[17210058.780000] sdb : READ CAPACITY failed.
[17210058.780000] sdb : status=0, message=00, host=7, driver=00
[17210058.780000] sdb : sense not available.
[17210058.800000] sdb: Write Protect is off
[17210058.800000] sdb: Mode Sense: 00 00 00 00
[17210058.800000] sdb: assuming drive cache: write through
[17210058.952000] sdb : READ CAPACITY failed.
[17210058.952000] sdb : status=0, message=00, host=7, driver=00
[17210058.952000] sdb : sense not available.
[17210058.980000] sdb: Write Protect is off
[17210058.980000] sdb: Mode Sense: 00 00 00 00
[17210058.980000] sdb: assuming drive cache: write through
[17210058.980000]  sdb:<3>Buffer I/O error on device sdb, logical block 0
[17210058.980000] Buffer I/O error on device sdb, logical block 0
[17210058.980000] Buffer I/O error on device sdb, logical block 0
[17210058.980000]  unable to read partition table
[17210059.056000] sdb : READ CAPACITY failed.
[17210059.056000] sdb : status=0, message=00, host=7, driver=00
[17210059.056000] sdb : sense not available.
[17210059.072000] sdb: Write Protect is off
[17210059.072000] sdb: Mode Sense: 00 00 00 00
[17210059.072000] sdb: assuming drive cache: write through
[17210059.140000] sdb : READ CAPACITY failed.
[17210059.140000] sdb : status=0, message=00, host=7, driver=00
[17210059.140000] sdb : sense not available.
[17210059.160000] sdb: Write Protect is off
[17210059.160000] sdb: Mode Sense: 00 00 00 00
[17210059.160000] sdb: assuming drive cache: write through
[17210059.160000]  sdb:<3>Buffer I/O error on device sdb, logical block 0
[17210059.160000] Buffer I/O error on device sdb, logical block 0
[17210059.160000] Buffer I/O error on device sdb, logical block 0
[17210059.160000]  unable to read partition table
[17210059.644000] usbcore: registered new driver usbserial
[17210059.644000] drivers/usb/serial/usb-serial.c: USB Serial support 
registered for generic
[17210059.648000] usbcore: registered new driver usbserial_generic
[17210059.648000] drivers/usb/serial/usb-serial.c: USB Serial Driver core
[17210059.660000] drivers/usb/serial/usb-serial.c: USB Serial support 
registered for Handspring Visor / Palm OS
[17210059.664000] drivers/usb/serial/usb-serial.c: USB Serial support 
registered for Sony Clie 3.5
[17210059.668000] drivers/usb/serial/usb-serial.c: USB Serial support 
registered for Sony Clie 5.0
[17210059.684000] usb 1-2: Handspring Visor / Palm OS: port 1, is for Generic 
use
[17210059.684000] usb 1-2: Handspring Visor / Palm OS: port 2, is for HotSync 
use
[17210059.684000] usb 1-2: Handspring Visor / Palm OS: Number of ports: 2
[17210059.688000] visor 1-2:1.0: Handspring Visor / Palm OS converter detected
[17210059.692000] usb 1-2: Handspring Visor / Palm OS converter now attached 
to ttyUSB0
[17210059.696000] usb 1-2: Handspring Visor / Palm OS converter now attached 
to ttyUSB1
[17210059.696000] usbcore: registered new driver visor
[17210059.696000] drivers/usb/serial/visor.c: USB HandSpring Visor / Palm OS 
driver
[17210060.552000] hub 1-0:1.0: port 1 disabled by hub (EMI?), re-enabling...
[17210060.552000] usb 1-1: USB disconnect, address 2
[17210060.552000] usb 1-1.1: USB disconnect, address 3
[17210060.552000] usb 1-1.2: USB disconnect, address 4
[17210060.552000] usb 1-1.3: USB disconnect, address 5
[17210222.540000] scsi1: PCI error Interrupt at seqaddr = 0x7
[17210222.540000] scsi1: Data Parity Error Detected during address or write 
data phase

On Monday 06 November 2006 5:51 am, Craig White wrote:
> I don't know what is causing the PCI parity errors but that doesn't look
> good...perhaps there is something amiss in BIOS - perhaps the best thing
> you can do is to remove all forced assignments in BIOS . ind let PCI & the
> OS handle interrupts.
>
> anyway, the command was to 'tail -n 20 dmesg' which as you found out
> didn't work
>
> this does work though...
>
> dmesg|tail -n 20
>
> Craig
>
> On Sun, 2006-11-05 at 22:23 -0700, Michael Havens wrote:
> > On Sunday 05 November 2006 8:00 pm, Craig White wrote:
> > > sudo tail -n 20 dmesg
> >
> > 1- bmike1 at 0[src]$ cd /media
> > 2- bmike1 at 0[media]$ ls
> > 3- cdrom  floppy
> > 4- bmike1 at 0[media]$ ls
> > 5- cdrom  floppy
> > 6- bmike1 at 0[media]$ ls
> > 5- cdrom  floppy
> > 6- bmike1 at 0[media]$
> >
> > line 2- baseline
> > line 4- after plug camera in
> > line 6- after press sync button
> >
> > first dmesg- baseline
> > second dmesg- plugged in
> > third dmesg - sync pressed
> >
> > bmike1 at 0[media]$ sudo dmesg -n 20
> > klogctl: Invalid argument
> > bmike1 at 0[media]$ man dmesg <-s = buffer size>
> > bmike1 at 0[media]$ dmesg -s 20
> > a Parity Error Detected during address or write data phase
> > [17211199.116000] scsi0: WARNING WARNING WARNING WARNING
> > [17211199.116000] scsi0: Too many PCI parity errors observed as a target.
> > [17211199.116000] scsi0: Some device on this bus is generating bad
> > parity. [17211199.116000] scsi0: This is an error *observed by*, not
> > *generated by*, this controller.
> > [17211199.116000] scsi0: PCI parity error checking has been disabled.
> > [17211199.116000] scsi0: WARNING WARNING WARNING WARNING
> > [17211233.060000] scsi0: PCI error Interrupt at seqaddr = 0x8
> > [17211233.060000] scsi0: Data Parity Error Detected during address or
> > write data phase
> > [17211233.060000] scsi0: WARNING WARNING WARNING WARNING
> > [17211233.060000] scsi0: Too many PCI parity errors observed as a target.
> > [17211233.060000] scsi0: Some device on this bus is generating bad
> > parity. [17211233.060000] scsi0: This is an error *observed by*, not
> > *generated by*, this controller.
> > [17211233.060000] scsi0: PCI parity error checking has been disabled.
> > [17211233.060000] scsi0: WARNING WARNING WARNING WARNING
> > [17211276.204000] scsi0: PCI error Interrupt at seqaddr = 0x7
> > [17211276.204000] scsi0: Data Parity Error Detected during address or
> > write data phase
> > [17211276.204000] scsi0: WARNING WARNING WARNING WARNING
> > [17211276.204000] scsi0: Too many PCI parity errors observed as a target.
> > [17211276.204000] scsi0: Some device on this bus is generating bad
> > parity. [17211276.204000] scsi0: This is an error *observed by*, not
> > *generated by*, this controller.
> > [17211276.204000] scsi0: PCI parity error checking has been disabled.
> > [17211276.204000] scsi0: WARNING WARNING WARNING WARNING
> > [17211298.168000] scsi0: PCI error Interrupt at seqaddr = 0x7
> > [17211298.168000] scsi0: Data Parity Error Detected during address or
> > write data phase
> > [17211298.168000] scsi0: WARNING WARNING WARNING WARNING
> > [17211298.168000] scsi0: Too many PCI parity errors observed as a target.
> > [17211298.168000] scsi0: Some device on this bus is generating bad
> > parity. [17211298.168000] scsi0: This is an error *observed by*, not
> > *generated by*, this controller.
> > [17211298.168000] scsi0: PCI parity error checking has been disabled.
> > [17211298.168000] scsi0: WARNING WARNING WARNING WARNING
> > [17211350.512000] scsi0: PCI error Interrupt at seqaddr = 0x8
> > [17211350.512000] scsi0: Data Parity Error Detected during address or
> > write data phase
> > [17211350.512000] scsi0: WARNING WARNING WARNING WARNING
> > [17211350.512000] scsi0: Too many PCI parity errors observed as a target.
> > [17211350.512000] scsi0: Some device on this bus is generating bad
> > parity. [17211350.512000] scsi0: This is an error *observed by*, not
> > *generated by*, this controller.
> > [17211350.512000] scsi0: PCI parity error checking has been disabled.
> > [17211350.512000] scsi0: WARNING WARNING WARNING WARNING
> > [17211383.680000] scsi0: PCI error Interrupt at seqaddr = 0x9
> > [17211383.680000] scsi0: Data Parity Error Detected during address or
> > write data phase
> > [17211383.680000] scsi0: WARNING WARNING WARNING WARNING
> > [17211383.680000] scsi0: Too many PCI parity errors observed as a target.
> > [17211383.680000] scsi0: Some device on this bus is generating bad
> > parity. [17211383.680000] scsi0: This is an error *observed by*, not
> > *generated by*, this controller.
> > [17211383.680000] scsi0: PCI parity error checking has been disabled.
> > [17211383.680000] scsi0: WARNING WARNING WARNING WARNING
> > [17211408.232000] scsi0: PCI error Interrupt at seqaddr = 0x9
> > [17211408.232000] scsi0: Data Parity Error Detected during address or
> > write data phase
> > [17211408.232000] scsi0: WARNING WARNING WARNING WARNING
> > [17211408.232000] scsi0: Too many PCI parity errors observed as a target.
> > [17211408.232000] scsi0: Some device on this bus is generating bad
> > parity. [17211408.232000] scsi0: This is an error *observed by*, not
> > *generated by*, this controller.
> > [17211408.232000] scsi0: PCI parity error checking has been disabled.
> > [17211408.232000] scsi0: WARNING WARNING WARNING WARNING
> >
> > bmike1 at 0[media]$ dmesg -s 20
> > a Parity Error Detected during address or write data phase
> > [17211199.116000] scsi0: WARNING WARNING WARNING WARNING
> > [17211199.116000] scsi0: Too many PCI parity errors observed as a target.
> > [17211199.116000] scsi0: Some device on this bus is generating bad
> > parity. [17211199.116000] scsi0: This is an error *observed by*, not
> > *generated by*, this controller.
> > [17211199.116000] scsi0: PCI parity error checking has been disabled.
> > [17211199.116000] scsi0: WARNING WARNING WARNING WARNING
> > [17211233.060000] scsi0: PCI error Interrupt at seqaddr = 0x8
> > [17211233.060000] scsi0: Data Parity Error Detected during address or
> > write data phase
> > [17211233.060000] scsi0: WARNING WARNING WARNING WARNING
> > [17211233.060000] scsi0: Too many PCI parity errors observed as a target.
> > [17211233.060000] scsi0: Some device on this bus is generating bad
> > parity. [17211233.060000] scsi0: This is an error *observed by*, not
> > *generated by*, this controller.
> > [17211233.060000] scsi0: PCI parity error checking has been disabled.
> > [17211233.060000] scsi0: WARNING WARNING WARNING WARNING
> > [17211276.204000] scsi0: PCI error Interrupt at seqaddr = 0x7
> > [17211276.204000] scsi0: Data Parity Error Detected during address or
> > write data phase
> > [17211276.204000] scsi0: WARNING WARNING WARNING WARNING
> > [17211276.204000] scsi0: Too many PCI parity errors observed as a target.
> > [17211276.204000] scsi0: Some device on this bus is generating bad
> > parity. [17211276.204000] scsi0: This is an error *observed by*, not
> > *generated by*, this controller.
> > [17211276.204000] scsi0: PCI parity error checking has been disabled.
> > [17211276.204000] scsi0: WARNING WARNING WARNING WARNING
> > [17211298.168000] scsi0: PCI error Interrupt at seqaddr = 0x7
> > [17211298.168000] scsi0: Data Parity Error Detected during address or
> > write data phase
> > [17211298.168000] scsi0: WARNING WARNING WARNING WARNING
> > [17211298.168000] scsi0: Too many PCI parity errors observed as a target.
> > [17211298.168000] scsi0: Some device on this bus is generating bad
> > parity. [17211298.168000] scsi0: This is an error *observed by*, not
> > *generated by*, this controller.
> > [17211298.168000] scsi0: PCI parity error checking has been disabled.
> > [17211298.168000] scsi0: WARNING WARNING WARNING WARNING
> > [17211350.512000] scsi0: PCI error Interrupt at seqaddr = 0x8
> > [17211350.512000] scsi0: Data Parity Error Detected during address or
> > write data phase
> > [17211350.512000] scsi0: WARNING WARNING WARNING WARNING
> > [17211350.512000] scsi0: Too many PCI parity errors observed as a target.
> > [17211350.512000] scsi0: Some device on this bus is generating bad
> > parity. [17211350.512000] scsi0: This is an error *observed by*, not
> > *generated by*, this controller.
> > [17211350.512000] scsi0: PCI parity error checking has been disabled.
> > [17211350.512000] scsi0: WARNING WARNING WARNING WARNING
> > [17211383.680000] scsi0: PCI error Interrupt at seqaddr = 0x9
> > [17211383.680000] scsi0: Data Parity Error Detected during address or
> > write data phase
> > [17211383.680000] scsi0: WARNING WARNING WARNING WARNING
> > [17211383.680000] scsi0: Too many PCI parity errors observed as a target.
> > [17211383.680000] scsi0: Some device on this bus is generating bad
> > parity. [17211383.680000] scsi0: This is an error *observed by*, not
> > *generated by*, this controller.
> > [17211383.680000] scsi0: PCI parity error checking has been disabled.
> > [17211383.680000] scsi0: WARNING WARNING WARNING WARNING
> > [17211408.232000] scsi0: PCI error Interrupt at seqaddr = 0x9
> > [17211408.232000] scsi0: Data Parity Error Detected during address or
> > write data phase
> > [17211408.232000] scsi0: WARNING WARNING WARNING WARNING
> > [17211408.232000] scsi0: Too many PCI parity errors observed as a target.
> > [17211408.232000] scsi0: Some device on this bus is generating bad
> > parity. [17211408.232000] scsi0: This is an error *observed by*, not
> > *generated by*, this controller.
> > [17211408.232000] scsi0: PCI parity error checking has been disabled.
> > [17211408.232000] scsi0: WARNING WARNING WARNING WARNING
> >
> > bmike1 at 0[media]$ dmesg -s 20
> > a Parity Error Detected during address or write data phase
> > [17211233.060000] scsi0: WARNING WARNING WARNING WARNING
> > [17211233.060000] scsi0: Too many PCI parity errors observed as a target.
> > [17211233.060000] scsi0: Some device on this bus is generating bad
> > parity. [17211233.060000] scsi0: This is an error *observed by*, not
> > *generated by*, this controller.
> > [17211233.060000] scsi0: PCI parity error checking has been disabled.
> > [17211233.060000] scsi0: WARNING WARNING WARNING WARNING
> > [17211276.204000] scsi0: PCI error Interrupt at seqaddr = 0x7
> > [17211276.204000] scsi0: Data Parity Error Detected during address or
> > write data phase
> > [17211276.204000] scsi0: WARNING WARNING WARNING WARNING
> > [17211276.204000] scsi0: Too many PCI parity errors observed as a target.
> > [17211276.204000] scsi0: Some device on this bus is generating bad
> > parity. [17211276.204000] scsi0: This is an error *observed by*, not
> > *generated by*, this controller.
> > [17211276.204000] scsi0: PCI parity error checking has been disabled.
> > [17211276.204000] scsi0: WARNING WARNING WARNING WARNING
> > [17211298.168000] scsi0: PCI error Interrupt at seqaddr = 0x7
> > [17211298.168000] scsi0: Data Parity Error Detected during address or
> > write data phase
> > [17211298.168000] scsi0: WARNING WARNING WARNING WARNING
> > [17211298.168000] scsi0: Too many PCI parity errors observed as a target.
> > [17211298.168000] scsi0: Some device on this bus is generating bad
> > parity. [17211298.168000] scsi0: This is an error *observed by*, not
> > *generated by*, this controller.
> > [17211298.168000] scsi0: PCI parity error checking has been disabled.
> > [17211298.168000] scsi0: WARNING WARNING WARNING WARNING
> > [17211350.512000] scsi0: PCI error Interrupt at seqaddr = 0x8
> > [17211350.512000] scsi0: Data Parity Error Detected during address or
> > write data phase
> > [17211350.512000] scsi0: WARNING WARNING WARNING WARNING
> > [17211350.512000] scsi0: Too many PCI parity errors observed as a target.
> > [17211350.512000] scsi0: Some device on this bus is generating bad
> > parity. [17211350.512000] scsi0: This is an error *observed by*, not
> > *generated by*, this controller.
> > [17211350.512000] scsi0: PCI parity error checking has been disabled.
> > [17211350.512000] scsi0: WARNING WARNING WARNING WARNING
> > [17211383.680000] scsi0: PCI error Interrupt at seqaddr = 0x9
> > [17211383.680000] scsi0: Data Parity Error Detected during address or
> > write data phase
> > [17211383.680000] scsi0: WARNING WARNING WARNING WARNING
> > [17211383.680000] scsi0: Too many PCI parity errors observed as a target.
> > [17211383.680000] scsi0: Some device on this bus is generating bad
> > parity. [17211383.680000] scsi0: This is an error *observed by*, not
> > *generated by*, this controller.
> > [17211383.680000] scsi0: PCI parity error checking has been disabled.
> > [17211383.680000] scsi0: WARNING WARNING WARNING WARNING
> > [17211408.232000] scsi0: PCI error Interrupt at seqaddr = 0x9
> > [17211408.232000] scsi0: Data Parity Error Detected during address or
> > write data phase
> > [17211408.232000] scsi0: WARNING WARNING WARNING WARNING
> > [17211408.232000] scsi0: Too many PCI parity errors observed as a target.
> > [17211408.232000] scsi0: Some device on this bus is generating bad
> > parity. [17211408.232000] scsi0: This is an error *observed by*, not
> > *generated by*, this controller.
> > [17211408.232000] scsi0: PCI parity error checking has been disabled.
> > [17211408.232000] scsi0: WARNING WARNING WARNING WARNING
> > [17211451.860000] scsi0: PCI error Interrupt at seqaddr = 0x8
> > [17211451.860000] scsi0: Data Parity Error Detected during address or
> > write data phase
> > [17211451.860000] scsi0: WARNING WARNING WARNING WARNING
> > [17211451.860000] scsi0: Too many PCI parity errors observed as a target.
> > [17211451.860000] scsi0: Some device on this bus is generating bad
> > parity. [17211451.860000] scsi0: This is an error *observed by*, not
> > *generated by*, this controller.
> > [17211451.860000] scsi0: PCI parity error checking has been disabled.
> > [17211451.860000] scsi0: WARNING WARNING WARNING WARNING
> > bmike1 at 0[media]$
> > ---------------------------------------------------
> > PLUG-discuss mailing list - PLUG-discuss at lists.plug.phoenix.az.us
> > To subscribe, unsubscribe, or to change  you mail settings:
> > http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss
>
> ---------------------------------------------------
> PLUG-discuss mailing list - PLUG-discuss at lists.plug.phoenix.az.us
> To subscribe, unsubscribe, or to change  you mail settings:
> http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss