trouble connecting to @home cable modem

[Jose D Castillo]

Call your cable company and make sure they can see your modem, they should
be able to see it even it you have no computers connected to it. Then
find out if they can give you a static address scheme. It can save you 
time to use static instead of DHCP. If they can, then make sure they give
you the following information: 

Static IP adress
Default Gateway
Netmask
DNS servers

If they can't, then you are at their mercy. You said you set up your
interface for DHCP and your output indicates you got and IP address, but
you may not be getting default route and DNS information. Call them and
ask them for that information. If they have their DHCP server setup right,
you should get that info when you connect, but it doesn't look like you
are, that is why I suggest going the static route.
Good Luck!

Live long and prosper.

On Sun, 24 Dec 2000, Tim Cutler wrote:

> After vast efforts scouring the net and reading man pages and HOWTO's, I
> still can't get my new RH 7 linux box to connect to the internet via
> cox@home cable modem.
> 
> Can anyone shed light on the tcpdump data below, at the bottom? To me,
> it looks like my box is asking for the MAC address of the gateway, and
> getting no response. In fact, I get the same output if I take off the
> cable connection. Hence, the connection is dead as a door nail. I've
> done dhcpcd -h CX538-A eth0, and countless other things.
> 
> If you have solved this problem, I'd would sure like to get in contact
> with you. I'm pretty much stumped at this point.
> 
> ------------------------------------------------------------------
> ifconfig output:
> 
> eth0      Link encap:Ethernet  HWaddr 00:50:BA:44:77:09
>           inet addr:24.1.249.49  Bcast:24.1.255.255  Mask:255.255.248.0
>           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
>           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>           TX packets:24 errors:0 dropped:0 overruns:0 carrier:0
>           collisions:0 txqueuelen:100
>           Interrupt:10 Base address:0xe800
> 
> lo        Link encap:Local Loopback
>           inet addr:127.0.0.1  Mask:255.0.0.0
>           UP LOOPBACK RUNNING  MTU:3924  Metric:1
>           RX packets:1917 errors:0 dropped:0 overruns:0 frame:0
>           TX packets:1917 errors:0 dropped:0 overruns:0 carrier:0
>           collisions:0 txqueuelen:0
> 
> ------------------------------------------------------------------
> netstat -nr output:
> 
> Kernel IP routing table
> Destination     Gateway         Genmask         Flags   MSS Window  irtt
> Iface
> 24.1.248.0      0.0.0.0         255.255.248.0   U         0 0          0
> eth0
> 127.0.0.0       0.0.0.0         255.0.0.0       U         0 0          0
> lo
> 0.0.0.0         24.1.248.1      0.0.0.0         UG        0 0          0
> eth0
> 0.0.0.0         24.1.248.1      0.0.0.0         UG        0 0          0
> eth0
> 
> ------------------------------------------------------------------
> ping 24.1.248.1 output:
> PING 24.1.248.1 (24.1.248.1) from 24.1.249.49 : 56(84) bytes of data.
> From 24.1.249.49: Destination Host Unreachable
> From 24.1.249.49: Destination Host Unreachable
> From 24.1.249.49: Destination Host Unreachable
> ...
> 
> ------------------------------------------------------------------
> tcpdump -i eth0 output:
> Kernel filter, protocol ALL, datagram packet socket
> tcpdump: listening on eth0
> 16:19:40.380943 > arp who-has 24.1.248.1 tell 24.1.249.49
> (0:50:ba:44:77:9)
> 16:19:41.381069 > arp who-has 24.1.248.1 tell 24.1.249.49
> (0:50:ba:44:77:9)
> 16:19:42.380945 > arp who-has 24.1.248.1 tell 24.1.249.49
> (0:50:ba:44:77:9)
> 16:19:43.380948 > arp who-has 24.1.248.1 tell 24.1.249.49
> (0:50:ba:44:77:9)
> ...
> 
> 
> ________________________________________________
> See http://PLUG.phoenix.az.us/navigator-mail.shtml if your mail doesn't post to the list quickly and you use Netscape to write mail.
> 
> Plug-discuss mailing list  -  Plug-discuss@lists.PLUG.phoenix.az.us
> http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss
>