68C under load is good. 80C+ idle is bad.
lets get back to heat... last time I was running glx (with the horse
and various other pictures) and watch, and stress ng the temp was like
68. I don't think that is too bad.
On Thu, Jul 16, 2020 at 3:19 PM Brian Cluff via PLUG-discuss
<plug-discuss@lists.phxlinux.org> wrote:
>
> Looks like your drive probably isn't the problem.
>
> Brian Cluff
>
> On 7/16/20 11:54 AM, Michael via PLUG-discuss wrote:
> > On Thu, Jul 16, 2020 at 3:37 AM Brian Cluff via PLUG-discuss
> > <plug-discuss@lists.phxlinux.org> wrote:
> >> Also check the health of your hard drive with smartctl. I've hard
> >> systems freeze on me because my hard drive was dying that then appear to
> >> work again for a while after a reboot. Basically your drive starts
> >> throwing errors and eventually the system remounts it as read only and
> >> your system eventually freaks out and freezes because it can't write to
> >> the drive anymore.
> > I sure hope this is the problem. It'll give me an excuse to put an ssd
> > in the machine.
> > This is from live media boot. I'll see if I can freeze the system
> > again.... it did when I tried it before but it hasn't frozen for a
> > couple of days now.
> > sudo smartctl --all /dev/sda
> > smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-26-generic] (local build)
> > Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
> >
> > === START OF INFORMATION SECTION ===
> > Model Family: Western Digital Caviar Blue (SATA)
> > Device Model: WDC WD3200AAKS-75L9A0
> > Serial Number: WD-WMAV2S110171
> > LU WWN Device Id: 5 0014ee 057775228
> > Firmware Version: 02.03E02
> > User Capacity: 320,072,933,376 bytes [320 GB]
> > Sector Size: 512 bytes logical/physical
> > Device is: In smartctl database [for details use: -P show]
> > ATA Version is: ATA8-ACS (minor revision not indicated)
> > SATA Version is: SATA 2.5, 3.0 Gb/s
> > Local Time is: Thu Jul 16 18:33:20 2020 UTC
> > SMART support is: Available - device has SMART capability.
> > SMART support is: Enabled
> >
> > === START OF READ SMART DATA SECTION ===
> > SMART overall-health self-assessment test result: PASSED
> >
> > General SMART Values:
> > Offline data collection status: (0x84) Offline data collection activity
> > was suspended by an interrupting command from host.
> > Auto Offline Data Collection: Enabled.
> > Self-test execution status: ( 0) The previous self-test
> > routine completed
> > without error or no self-test has ever
> > been run.
> > Total time to complete Offline
> > data collection: ( 6000) seconds.
> > Offline data collection
> > capabilities: (0x7b) SMART execute Offline immediate.
> > Auto Offline data collection on/off support.
> > Suspend Offline collection upon new
> > command.
> > Offline surface scan supported.
> > Self-test supported.
> > Conveyance Self-test supported.
> > Selective Self-test supported.
> > SMART capabilities: (0x0003) Saves SMART data before entering
> > power-saving mode.
> > Supports SMART auto save timer.
> > Error logging capability: (0x01) Error logging supported.
> > General Purpose Logging supported.
> > Short self-test routine
> > recommended polling time: ( 2) minutes.
> > Extended self-test routine
> > recommended polling time: ( 73) minutes.
> > Conveyance self-test routine
> > recommended polling time: ( 5) minutes.
> > SCT capabilities: (0x3037) SCT Status supported.
> > SCT Feature Control supported.
> > SCT Data Table supported.
> >
> > SMART Attributes Data Structure revision number: 16
> > Vendor Specific SMART Attributes with Thresholds:
> > ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
> > UPDATED WHEN_FAILED RAW_VALUE
> > 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail
> > Always - 0
> > 3 Spin_Up_Time 0x0027 138 133 021 Pre-fail
> > Always - 4075
> > 4 Start_Stop_Count 0x0032 089 089 000 Old_age
> > Always - 11090
> > 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail
> > Always - 0
> > 7 Seek_Error_Rate 0x002e 100 253 000 Old_age
> > Always - 0
> > 9 Power_On_Hours 0x0032 019 019 000 Old_age
> > Always - 59593
> > 10 Spin_Retry_Count 0x0032 100 100 000 Old_age
> > Always - 0
> > 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age
> > Always - 0
> > 12 Power_Cycle_Count 0x0032 098 098 000 Old_age
> > Always - 2282
> > 192 Power-Off_Retract_Count 0x0032 199 199 000 Old_age
> > Always - 1044
> > 193 Load_Cycle_Count 0x0032 197 197 000 Old_age
> > Always - 11090
> > 194 Temperature_Celsius 0x0022 105 080 000 Old_age
> > Always - 38
> > 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age
> > Always - 0
> > 197 Current_Pending_Sector 0x0032 200 200 000 Old_age
> > Always - 0
> > 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age
> > Offline - 0
> > 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age
> > Always - 0
> > 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age
> > Offline - 0
> > 240 Head_Flying_Hours 0x0032 024 024 000 Old_age
> > Always - 55990
> > 241 Total_LBAs_Written 0x0032 200 200 000 Old_age
> > Always - 78243499218
> > 242 Total_LBAs_Read 0x0032 200 200 000 Old_age
> > Always - 174621575474
> >
> > SMART Error Log Version: 1
> > No Errors Logged
> >
> > SMART Self-test log structure revision number 1
> > Num Test_Description Status Remaining
> > LifeTime(hours) LBA_of_first_error
> > # 1 Short offline Completed without error 00% 14352 -
> > # 2 Short offline Completed without error 00% 0 -
> >
> > SMART Selective self-test log data structure revision number 1
> > SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
> > 1 0 0 Not_testing
> > 2 0 0 Not_testing
> > 3 0 0 Not_testing
> > 4 0 0 Not_testing
> > 5 0 0 Not_testing
> > Selective self-test flags (0x0):
> > After scanning selected spans, do NOT read-scan remainder of disk.
> > If Selective self-test is pending on power-up, resume after 0 minute delay.
> >
> > Well, I am running glmark2, watch, and stress-ng for about (one round
> > of glmark2) with no freeze. all from live media
> > --
> > :-)~MIKE~(-:
> > ---------------------------------------------------
> > PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org
> > To subscribe, unsubscribe, or to change your mail settings:
> > https://lists.phxlinux.org/mailman/listinfo/plug-discuss
>
> ---------------------------------------------------
> PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org
> To subscribe, unsubscribe, or to change your mail settings:
> https://lists.phxlinux.org/mailman/listinfo/plug-discuss
--
:-)~MIKE~(-:
---------------------------------------------------
PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org
To subscribe, unsubscribe, or to change your mail settings:
https://lists.phxlinux.org/mailman/listinfo/plug-discuss
--
A mouse trap, placed on top of your alarm clock, will prevent you from rolling over and going back to sleep after you hit the snooze button.
Stephen
---------------------------------------------------
PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org
To subscribe, unsubscribe, or to change your mail settings:
https://lists.phxlinux.org/mailman/listinfo/plug-discuss