okay; if you get the 'bad superblock' error when attempting to mount a drive you did something to the drives filesystem which prevents it from mounting through the GUI. The solution to this is to mount the drive through the terminal (CLI?) (ohhhhh.... command line interface) and copy the files to a new drive with the CLI and reformat the drive. you can tell the device in the bad superblock error message. ChatGPT said that the error was in the filesystem and is not easily repaired. On Fri, Nov 8, 2024 at 5:50 AM Michael wrote: > Thank You gentlemen. I'll get to this as soon as I get home. Thank you so > much for your help. > > On Thu, Nov 7, 2024, 2:46 PM Rusty Carruth via PLUG-discuss < > plug-discuss@lists.phxlinux.org> wrote: > >> gparted, Under the 'Device/Attempt data rescue' dropdown can attempt to >> find things. Don't think it can recover, but it can mount them so you >> can copy off. >> >> Backing up a bit, first let me explain a bit about the icon (or at >> least, what I think you're talking about) >> >> So, some systems, when they detect a mountable partition, will put an >> icon on the desktop that allows you to click (double-click? whatever) >> it and get the partition mounted. >> >> A partition which is already mounted is, by definition, not mountable >> (slight white lie). So, that same system (should) remove the icon since >> the partition is not mountable. >> >> So, that's why the icon goes away when you mount it manually. >> >> So, don't let that distract you from the major quest, which I believe is >> to make the partition 'work normally'. >> >> First, when you mount it from the command line, do you get a warning of >> some kind? >> >> If not, type 'mount |less' (or, if you just mounted say /dev/sdb1, say >> 'mount | grep sdb1') and find your device - does it say ro or rw >> somewhere? RO means read-only, RW means read-write. I'm guessing your >> device will show RO and not RW. >> >> (here's my /dev/sdb2, mounted normally: >> >> /dev/sdb2 on /home type ext4 (rw,relatime,errors=remount-ro) >> >> Note the rw. Mounted 'badly' would be: >> >> /dev/sdb2 on /home type ext4 (ro,relatime,errors=remount-ro) >> >> Before you proceed, I highly recommend doing an image backup of the >> device. If you have space on your hard disk, do the following unmount >> the partition (again, let's say it is /dev/sdb1), then make the image >> copy: dd if=/dev/sdb | gzip > my.device.backup.dd.gz >> >> This uses DD (HIGHLY recommend you check out ddrescue as a better >> alternative!!!!!) to copy, bit-for-bit, everything on the device >> /dev/sdb (note the whole device, not the partition. You can also copy >> just the partition, which may be useful for other things, by using the >> partition (/dev/sdb1) instead of the device). By not giving dd an 'of=' >> argument it sends the data to standard output, which you then compress >> and put into the backup file. If the worst happens and your recovery >> efforts destroy the data on the device, you can restore it. One reason >> for ALSO saving just the partition is that you can create a partition >> somewhere on a disk and write that partition image there... >> >> Ok, so you've got your backup. You can try fsck and whatever else >> (someone says that 'disk drill press kit' can do wonders, I have not >> tried it myself) to try to fix the problem. A lot depends upon what >> mount said when you mounted it manually. >> >> Worst case, copy all the files off the device. Make sure everything is >> there... then either get a new drive and put the data on it, or >> reformat the old one. I tend to keep old drives in that state laying >> around, but then if you did the image backup with dd you have, in >> effect, the original device just without the hardware... >> >> Hopefully enough of that made sense to get you going! >> >> On 11/7/24 09:03, Michael via PLUG-discuss wrote: >> > No luck. I did that and it is just running me around by the balls. I can >> > mount and view the files from the terminal but not the GUI. When I mount >> > the drive the icon disappears and when I double click the icon I get the >> > original error message. >> > >> > On Thu, Nov 7, 2024 at 8:10 AM wrote: >> > >> >> Hi Mike, >> >> >> >> Have no idea what you are dealing with. >> >> >> >> I went to https://chatgpt.com/ >> >> >> >> And entered "bad superblock...., missing codepage or helper program, or >> >> other error". >> >> >> >> Chat responded with a bunch of information. Enter at your own risk. >> >> >> >> Keith >> >> >> >> >> >> >> >> >> >> On 2024-11-07 06:03, Michael via PLUG-discuss wrote: >> >>> it says '... bad superblock...., missing codepage or helper program, >> >>> or other error'. it's probably the superblock and if I remember right >> >>> that can be fixed. Can someone tell me how to do so? >> >>> >> >>> On Thu, Nov 7, 2024 at 7:55 AM Michael wrote: >> >>> >> >>>> I screwed up. I clicked the unmount button, waited a couple of >> >>>> seconds, and then pulled the drive. Well, the unmount hadn't >> >>>> completed! I plugged the drive in but it won't open. OOpS! Anything >> >>>> I can do to save the drive and the information on it? >> >>> -- >> >>> >> >>> :-)~MIKE~(-: >> >>> --------------------------------------------------- >> >>> PLUG-discuss mailing list: PLUG-discuss@lists.phxlinux.org >> >>> To subscribe, unsubscribe, or to change your mail settings: >> >>> https://lists.phxlinux.org/mailman/listinfo/plug-discuss >> > >> > >> > --------------------------------------------------- >> > PLUG-discuss mailing list: PLUG-discuss@lists.phxlinux.org >> > To subscribe, unsubscribe, or to change your mail settings: >> > https://lists.phxlinux.org/mailman/listinfo/plug-discuss >> --------------------------------------------------- >> PLUG-discuss mailing list: PLUG-discuss@lists.phxlinux.org >> To subscribe, unsubscribe, or to change your mail settings: >> https://lists.phxlinux.org/mailman/listinfo/plug-discuss >> > -- :-)~MIKE~(-: