An interface that starts en is ethernet. Wireless interfaces should start wl. That is the rule for base hardware, I am unsure if this changes in a vm. On Feb 3, 2015 11:42 PM, "Michael Torres" wrote: > What is your "outside" interface you're bridging to? Where does the > "host" get it's address from? > > I am assuming your refering to my network adapter? in this case my > wireless adpater and yes, in my VBox config settings, I am choosing that > adapter > > If your familiar with VBox settings, here they are line by line... > > Attached To: Bridged Adapter > Name: Killer Wireless-n/a/ac 1525 Wireless Network Adapter > Adapter Type: Intel PRO/1000 MT Desktop (82540EM) > Promiscuous Mode: Deny > MAC address: 080027FFA0AC > Cable Connected: yes > > > I have verified that the MAC address is the same in my ifcfg-enp0s3 file. > > > > On Tue, Feb 3, 2015 at 11:14 PM, Michael Butash > wrote: > >> Sounds like you're binding to the wrong interface for your bridge for >> vbox. You shouldn't need to put it in promiscuous unless you're intending >> to sniff actually with wireshark or like. >> >> As asked, ifconfig -a would be helpful. >> >> What is your "outside" interface you're bridging to? Where does the >> "host" get it's address from? >> >> Make sure vbox is binding to "that" interface. >> >> I've not ever had an issue with that occurring unless picking the wrong >> interface on the system on wired. >> >> Ahh, yes on "wired". Wireless is different - depending on the wireless, >> the router/ap might not let you get another address. Enterprise (and >> commercial hotspot systems) wifi systems like cisco do things like dhcp >> binding for the host, disallowing you as the cpe device from binding with >> an additional mac address on that session as "bridged". Your only >> alternative at that point is to use the nat interface for translating you >> out via your acquired host address off an internal interface. >> >> -mb >> >> >> On 02/03/2015 08:07 PM, Michael Torres wrote: >> >> Hello all, >> >> I have an problem that I cannot seem to figure out..... >> >> I am trying to use "Bridged" networking in Virtual Box to a CentOS 7 >> minimum install distro that I want to use for my development server. >> >> I have used Bridged networking in the past and never had any issues but >> that was with older versions of CentOS >> >> The issue.... DHCP will not assign a IPv4 address to the server. >> >> Here is the weird part... I was at startbucks and actually got it to >> work! (Please, hold the "Just use it at starbucks then" comments..I >> know....) >> >> Here is the process I used... >> >> -Installed a fresh CentOS 7 on VBox >> -While on NAT, I performed "yum update" so my server was fresh with the >> latest >> -Disabled SELinux >> -Disabled the Firewall >> -Shut down server to reconfigure the adapter to "Bridged" >> -used adapter type of "Intel Pro 1000 MT Desktop (82540EM)" >> -set it to "Promiscuous Mode" >> -restart the server >> >> >> Again, at Starbucks it assigned a IP address, so this leads me to >> believe that the issue is with a configuration on my router. >> >> I am not very good at networking, so any help would be appreciated. >> >> If you need error messages or other output, let me know (and possibly >> the command as I don't know networking that well other than "ifconfig") >> >> >> Mike >> >> >> --------------------------------------------------- >> PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org >> To subscribe, unsubscribe, or to change your mail settings:http://lists.phxlinux.org/mailman/listinfo/plug-discuss >> >> >> >> --------------------------------------------------- >> PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org >> To subscribe, unsubscribe, or to change your mail settings: >> http://lists.phxlinux.org/mailman/listinfo/plug-discuss >> > > > --------------------------------------------------- > PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org > To subscribe, unsubscribe, or to change your mail settings: > http://lists.phxlinux.org/mailman/listinfo/plug-discuss >