Ok, sorry, I misunderstood. Nmap could be your friend here. Install it on your Windows machine. It will install the graphical tool automatically in Windows. Point this at your VM, and do a "intense scan" Next, on the Linux VM, do a # netstat -plant Zenmap/Nmap will tell you what ports it can see open from its side of the link. The netstat command will tell you which ports are opened by running software. Lastly, on the Linux VM, do a # ip tables -L This will tell you which ports the firewall will allow. Now, you have a few possibilities: 1) The netstat does not show the binding to port 21... this means SSHD did not start. 2) netstat shows SSHD, but the firewall is not allowing it. Open the firewall 3) netstat shows SSHD, the firewall is open, but you still don't see the port open via nmap. 3a) if you see other ports open, I would look at the Windows firewall 3b) If you don't see any ports open, you have two options here. 3b1) Make sure your NIC (from the Windows side) is in promiscuous mode. 3b2) If it is already in promiscuous mode, then this may not work in this configuration. In this case, try adding a private network on a second NIC, and communicate with the VM over that. Let me how it goes. Kevin On Feb 3, 2015 9:58 PM, "Michael Torres" wrote: > Well, no, I didnt issue any commands other than > /path/to/network/script/network start /path/to/network/script/network stop > and the commands to disable firewall/SELINUX > > I know I didnt use any systemctrl commands., but I tried to run the > commands that you just provided and nothing happened. I should probably > say that I know that IPv6 is enalbed and have network connection to the net > work and I can ping yahoo.com etc..... I just cant SSH(putty) to the > server. > > This all leads me to beleive that there is a configuration in my router > that is not allowing me to get a IPv4 address. Does the default gateway > have to be a certain number? I have manually configured that IP on my > router a long time ago, but even then I had Bridged networking working > correctly. > > Mike > > > > On Tue, Feb 3, 2015 at 9:48 PM, Kevin Fries wrote: > >> Your network is probably not getting started. The enp0p3 is the name of >> an interface started almost definantly by systemd, not the old RHEL way. >> This is likely why the networking-scripts didn't work. >> >> When you were at Starbucks, you likely did a systemctl start on the >> interface. Look in your history for it. If you find it, issue the same >> command again. If your interface comes up correctly, reissue the command >> once again, substituting enable for start. This second command is similar >> to a chkconfig command. >> >> Let me know how that works. >> >> Kevin >> On Feb 3, 2015 9:13 PM, "Michael Torres" wrote: >> >>> The result of that command is: >>> >>> 0 loaded units listed >>> >>> >>> So I ran a what it suggested: systemctl list-unit-files >>> majority of everything says "static" but some are "enabled" or >>> "disabled" >>> >>> again, because I cannot copy or capture a screen shot, is there a >>> specific list item that you need to see?" >>> >>> >>> >>> >>> >>> On Tue, Feb 3, 2015 at 8:44 PM, Kevin Fries >>> wrote: >>> >>>> Do a >>>> >>>> # systemctl --failed >>>> >>>> And post the results >>>> >>>> Kevin >>>> On Feb 3, 2015 8:37 PM, "Michael Torres" wrote: >>>> >>>>> Arrghh....yes its configured. But I am having an issue getting the >>>>> cat /etc/sysconfig/network-script/ifcfg-enp0s3..........because I cant >>>>> connect, I cant ssh in to use outty so I can copy using my mouse. I tried >>>>> taking a screen shot, but VBox for some reason wont display on on the >>>>> "print screen"command. >>>>> >>>>> is there a particular setting you are looking for? again, the file is >>>>> configured and it is reading it. >>>>> >>>>> Mike >>>>> >>>>> On Tue, Feb 3, 2015 at 8:15 PM, Stephen M >>>>> wrote: >>>>> >>>>>> I don't remember if this is a problem in centos 7 as it was in 6. >>>>>> But check to make sure the eth0 is configured. But yes a print out of >>>>>> ifconfig inside vox would be great. >>>>>> On Feb 3, 2015 8:07 PM, "Michael Torres" >>>>>> wrote: >>>>>> >>>>>>> Hello all, >>>>>>> >>>>>>> I have an problem that I cannot seem to figure out..... >>>>>>> >>>>>>> I am trying to use "Bridged" networking in Virtual Box to a CentOS 7 >>>>>>> minimum install distro that I want to use for my development server. >>>>>>> >>>>>>> I have used Bridged networking in the past and never had any issues >>>>>>> but that was with older versions of CentOS >>>>>>> >>>>>>> The issue.... DHCP will not assign a IPv4 address to the server. >>>>>>> >>>>>>> Here is the weird part... I was at startbucks and actually got it >>>>>>> to work! (Please, hold the "Just use it at starbucks then" comments..I >>>>>>> know....) >>>>>>> >>>>>>> Here is the process I used... >>>>>>> >>>>>>> -Installed a fresh CentOS 7 on VBox >>>>>>> -While on NAT, I performed "yum update" so my server was fresh with >>>>>>> the latest >>>>>>> -Disabled SELinux >>>>>>> -Disabled the Firewall >>>>>>> -Shut down server to reconfigure the adapter to "Bridged" >>>>>>> -used adapter type of "Intel Pro 1000 MT Desktop (82540EM)" >>>>>>> -set it to "Promiscuous Mode" >>>>>>> -restart the server >>>>>>> >>>>>>> >>>>>>> Again, at Starbucks it assigned a IP address, so this leads me to >>>>>>> believe that the issue is with a configuration on my router. >>>>>>> >>>>>>> I am not very good at networking, so any help would be appreciated. >>>>>>> >>>>>>> If you need error messages or other output, let me know (and >>>>>>> possibly the command as I don't know networking that well other than >>>>>>> "ifconfig") >>>>>>> >>>>>>> >>>>>>> Mike >>>>>>> >>>>>>> --------------------------------------------------- >>>>>>> PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org >>>>>>> To subscribe, unsubscribe, or to change your mail settings: >>>>>>> http://lists.phxlinux.org/mailman/listinfo/plug-discuss >>>>>>> >>>>>> >>>>>> --------------------------------------------------- >>>>>> PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org >>>>>> To subscribe, unsubscribe, or to change your mail settings: >>>>>> http://lists.phxlinux.org/mailman/listinfo/plug-discuss >>>>>> >>>>> >>>>> >>>>> --------------------------------------------------- >>>>> PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org >>>>> To subscribe, unsubscribe, or to change your mail settings: >>>>> http://lists.phxlinux.org/mailman/listinfo/plug-discuss >>>>> >>>> >>>> --------------------------------------------------- >>>> PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org >>>> To subscribe, unsubscribe, or to change your mail settings: >>>> http://lists.phxlinux.org/mailman/listinfo/plug-discuss >>>> >>> >>> >>> --------------------------------------------------- >>> PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org >>> To subscribe, unsubscribe, or to change your mail settings: >>> http://lists.phxlinux.org/mailman/listinfo/plug-discuss >>> >> >> --------------------------------------------------- >> PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org >> To subscribe, unsubscribe, or to change your mail settings: >> http://lists.phxlinux.org/mailman/listinfo/plug-discuss >> > > > --------------------------------------------------- > PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org > To subscribe, unsubscribe, or to change your mail settings: > http://lists.phxlinux.org/mailman/listinfo/plug-discuss >