unplugging it was the first thing I tried. Then I tried to fix it with a reboot (that fixed things for me before when dealing with things. :-)~MIKE~(-: On Tue, May 6, 2014 at 2:18 PM, Michael Havens wrote: > bmike1@PresarioLapTop1:~$ /etc/init.d/autofs status > bash: /etc/init.d/autofs: No such file or directory > bmike1@PresarioLapTop1:~$ > bmike1@PresarioLapTop1:~$ ps |grep automount > bmike1@PresarioLapTop1:~$ > > > :-)~MIKE~(-: > > > On Tue, May 6, 2014 at 11:51 AM, Mike Ballon wrote: > >> unplug/plug, it should automount, if not check: >> >> $ /etc/init.d/autofs status >> >> automount (pid 1442) is running... >> >> >> On Tue, May 6, 2014 at 2:44 PM, Michael Havens wrote: >> >>> it isn't automounting. >>> >>> >>> :-)~MIKE~(-: >>> >>> >>> On Tue, May 6, 2014 at 11:41 AM, Michael Havens wrote: >>> >>>> got it all to work.... even changed the label name. What messed me up >>>> was: >>>> >>>> $> Command > 1 (press enter 3times) -- again maybe you don't need the >>>> one >>>> >>>> I didn't understand at first that was part of the 'n' command. >>>> >>>> >>>> bmike1@PresarioLapTop1:/media/bmike1/OpenELEC$ sudo fdisk /dev/sdd >>>> >>>> Command (m for help): o >>>> Building a new DOS disklabel with disk identifier 0x3e8c35b3. >>>> Changes will remain in memory only, until you decide to write them. >>>> After that, of course, the previous content won't be recoverable. >>>> >>>> Warning: invalid flag 0x0000 of partition table 4 will be corrected by >>>> w(rite) >>>> >>>> Command (m for help): n >>>> Partition type: >>>> p primary (0 primary, 0 extended, 4 free) >>>> e extended >>>> Select (default p): p >>>> Partition number (1-4, default 1): >>>> Using default value 1 >>>> First sector (2048-3913663, default 2048): >>>> Using default value 2048 >>>> Last sector, +sectors or +size{K,M,G} (2048-3913663, default 3913663): >>>> Using default value 3913663 >>>> >>>> Command (m for help): t >>>> Selected partition 1 >>>> Hex code (type L to list codes): ntfs >>>> Hex code (type L to list codes): >>>> Hex code (type L to list codes): l >>>> >>>> 0 Empty 24 NEC DOS 81 Minix / old Lin bf Solaris >>>> >>>> 1 FAT12 27 Hidden NTFS Win 82 Linux swap / So c1 >>>> DRDOS/sec (FAT- >>>> 2 XENIX root 39 Plan 9 83 Linux c4 >>>> DRDOS/sec (FAT- >>>> 3 XENIX usr 3c PartitionMagic 84 OS/2 hidden C: c6 >>>> DRDOS/sec (FAT- >>>> 4 FAT16 <32M 40 Venix 80286 85 Linux extended c7 Syrinx >>>> >>>> 5 Extended 41 PPC PReP Boot 86 NTFS volume set da Non-FS >>>> data >>>> 6 FAT16 42 SFS 87 NTFS volume set db CP/M / >>>> CTOS / . >>>> 7 HPFS/NTFS/exFAT 4d QNX4.x 88 Linux plaintext de Dell >>>> Utility >>>> 8 AIX 4e QNX4.x 2nd part 8e Linux LVM df BootIt >>>> >>>> 9 AIX bootable 4f QNX4.x 3rd part 93 Amoeba e1 DOS >>>> access >>>> a OS/2 Boot Manag 50 OnTrack DM 94 Amoeba BBT e3 DOS R/O >>>> >>>> b W95 FAT32 51 OnTrack DM6 Aux 9f BSD/OS e4 >>>> SpeedStor >>>> c W95 FAT32 (LBA) 52 CP/M a0 IBM Thinkpad hi eb BeOS fs >>>> >>>> e W95 FAT16 (LBA) 53 OnTrack DM6 Aux a5 FreeBSD ee GPT >>>> >>>> f W95 Ext'd (LBA) 54 OnTrackDM6 a6 OpenBSD ef EFI >>>> (FAT-12/16/ >>>> 10 OPUS 55 EZ-Drive a7 NeXTSTEP f0 >>>> Linux/PA-RISC b >>>> 11 Hidden FAT12 56 Golden Bow a8 Darwin UFS f1 >>>> SpeedStor >>>> 12 Compaq diagnost 5c Priam Edisk a9 NetBSD f4 >>>> SpeedStor >>>> 14 Hidden FAT16 <3 61 SpeedStor ab Darwin boot f2 DOS >>>> secondary >>>> 16 Hidden FAT16 63 GNU HURD or Sys af HFS / HFS+ fb VMware >>>> VMFS >>>> 17 Hidden HPFS/NTF 64 Novell Netware b7 BSDI fs fc VMware >>>> VMKCORE >>>> 18 AST SmartSleep 65 Novell Netware b8 BSDI swap fd Linux >>>> raid auto >>>> 1b Hidden W95 FAT3 70 DiskSecure Mult bb Boot Wizard hid fe LANstep >>>> >>>> 1c Hidden W95 FAT3 75 PC/IX be Solaris boot ff BBT >>>> >>>> 1e Hidden W95 FAT1 80 Old Minix >>>> Hex code (type L to list codes): 86 >>>> Changed system type of partition 1 to 86 (NTFS volume set) >>>> >>>> Command (m for help): b >>>> There is no *BSD partition on /dev/sdd. >>>> >>>> Command (m for help): p >>>> >>>> Disk /dev/sdd: 2003 MB, 2003795968 bytes >>>> 11 heads, 4 sectors/track, 88946 cylinders, total 3913664 sectors >>>> Units = sectors of 1 * 512 = 512 bytes >>>> Sector size (logical/physical): 512 bytes / 512 bytes >>>> I/O size (minimum/optimal): 512 bytes / 512 bytes >>>> Disk identifier: 0x3e8c35b3 >>>> >>>> Device Boot Start End Blocks Id System >>>> /dev/sdd1 2048 3913663 1955808 86 NTFS volume set >>>> >>>> Command (m for help): w >>>> The partition table has been altered! >>>> >>>> Calling ioctl() to re-read partition table. >>>> Syncing disks. >>>> bmike1@PresarioLapTop1:/media/bmike1/OpenELEC$ >>>> >>>> >>>> >>>> :-)~MIKE~(-: >>>> >>>> >>>> On Tue, May 6, 2014 at 11:23 AM, Mike Ballon wrote: >>>> >>>>> After the 1 is t, 1 might have been selected for you by default. >>>>> >>>>> start over... >>>>> >>>>> $> fdisk /dev/sdd >>>>> $> Command > o (create new table) >>>>> $> Command > n (create part, 1 would be the default, maybe you don't >>>>> need the 1) >>>>> $> Command > 1 (press enter 3times) -- again maybe you don't need the >>>>> one >>>>> $> Command > t (select fs type) >>>>> $> Command > b (selects fat for fs) >>>>> $> Command > p (print the table) >>>>> $> Command > w (write the changes) >>>>> >>>>> don't make me do a video I don't have time ;) >>>>> >>>>> >>>>> >>>>> On Tue, May 6, 2014 at 1:57 PM, Michael Havens wrote: >>>>> >>>>>> Okay.... I think I really screwed things up. YOu said: >>>>>> >>>>>> $> fdisk /dev/sdb >>>>>> $> Command > o >>>>>> $> Command > n >>>>>> $> Command > 1 (press enter 3times) >>>>>> $> Command > t >>>>>> $> Command > b >>>>>> $> Command > w >>>>>> $> Command > p >>>>>> >>>>>> ***The above didn't look like that. There was no '$>' >>>>>> But I figured your computer was just configured differently >>>>>> so I carried on! >>>>>> >>>>>> bmike1@PresarioLapTop1:/media/bmike1/OpenELEC$ sudo fdisk /dev/sdd >>>>>> >>>>>> Command (m for help): o >>>>>> Building a new DOS disklabel with disk identifier 0xf66cb38c. >>>>>> Changes will remain in memory only, until you decide to write them. >>>>>> After that, of course, the previous content won't be recoverable. >>>>>> >>>>>> Warning: invalid flag 0x0000 of partition table 4 will be corrected >>>>>> by w(rite) >>>>>> >>>>>> Command (m for help): n >>>>>> Partition type: >>>>>> p primary (0 primary, 0 extended, 4 free) >>>>>> e extended >>>>>> Select (default p): p >>>>>> Partition number (1-4, default 1): >>>>>> Using default value 1 >>>>>> First sector (2048-3913663, default 2048): >>>>>> Using default value 2048 >>>>>> Last sector, +sectors or +size{K,M,G} (2048-3913663, default >>>>>> 3913663): >>>>>> Using default value 3913663 >>>>>> >>>>>> Command (m for help): 1 >>>>>> 1: unknown command >>>>>> Command action >>>>>> a toggle a bootable flag >>>>>> b edit bsd disklabel >>>>>> c toggle the dos compatibility flag >>>>>> d delete a partition >>>>>> l list known partition types >>>>>> m print this menu >>>>>> n add a new partition >>>>>> o create a new empty DOS partition table >>>>>> p print the partition table >>>>>> q quit without saving changes >>>>>> s create a new empty Sun disklabel >>>>>> t change a partition's system id >>>>>> u change display/entry units >>>>>> v verify the partition table >>>>>> w write table to disk and exit >>>>>> x extra functionality (experts only) >>>>>> >>>>>> Command (m for help): t >>>>>> Selected partition 1 >>>>>> Hex code (type L to list codes): >>>>>> Hex code (type L to list codes): w >>>>>> Hex code (type L to list codes): ^[^[ >>>>>> Hex code (type L to list codes): >>>>>> Hex code (type L to list codes): ^Cbmike1@PresarioLapTop1:/media/bmike1/OpenELEC$ >>>>>> sudo fdisk /dev/sdd >>>>>> >>>>>> Command (m for help): o >>>>>> Building a new DOS disklabel with disk identifier 0xbdd16f92. >>>>>> Changes will remain in memory only, until you decide to write them. >>>>>> After that, of course, the previous content won't be recoverable. >>>>>> >>>>>> Warning: invalid flag 0x0000 of partition table 4 will be corrected >>>>>> by w(rite) >>>>>> >>>>>> Command (m for help): n >>>>>> Partition type: >>>>>> p primary (0 primary, 0 extended, 4 free) >>>>>> e extended >>>>>> Select (default p): b >>>>>> Invalid partition type `b' >>>>>> >>>>>> Command (m for help): n >>>>>> Partition type: >>>>>> p primary (0 primary, 0 extended, 4 free) >>>>>> e extended >>>>>> Select (default p): p >>>>>> Partition number (1-4, default 1): >>>>>> Using default value 1 >>>>>> First sector (2048-3913663, default 2048): >>>>>> Using default value 2048 >>>>>> Last sector, +sectors or +size{K,M,G} (2048-3913663, default >>>>>> 3913663): >>>>>> Using default value 3913663 >>>>>> >>>>>> Command (m for help): b >>>>>> There is no *BSD partition on /dev/sdd. >>>>>> >>>>>> Command (m for help): w >>>>>> The partition table has been altered! >>>>>> >>>>>> Calling ioctl() to re-read partition table. >>>>>> Syncing disks. >>>>>> bmike1@PresarioLapTop1:/media/bmike1/OpenELEC$ sudo fdisk /dev/sdd >>>>>> >>>>>> Command (m for help): p >>>>>> >>>>>> Disk /dev/sdd: 2003 MB, 2003795968 bytes >>>>>> 11 heads, 4 sectors/track, 88946 cylinders, total 3913664 sectors >>>>>> Units = sectors of 1 * 512 = 512 bytes >>>>>> Sector size (logical/physical): 512 bytes / 512 bytes >>>>>> I/O size (minimum/optimal): 512 bytes / 512 bytes >>>>>> Disk identifier: 0xbdd16f92 >>>>>> >>>>>> Device Boot Start End Blocks Id System >>>>>> /dev/sdd1 2048 3913663 1955808 83 Linux >>>>>> >>>>>> Command (m for help): ^[[B^[[A^[ >>>>>> [: unknown command >>>>>> Command action >>>>>> a toggle a bootable flag >>>>>> b edit bsd disklabel >>>>>> c toggle the dos compatibility flag >>>>>> d delete a partition >>>>>> l list known partition types >>>>>> m print this menu >>>>>> n add a new partition >>>>>> o create a new empty DOS partition table >>>>>> p print the partition table >>>>>> q quit without saving changes >>>>>> s create a new empty Sun disklabel >>>>>> t change a partition's system id >>>>>> u change display/entry units >>>>>> v verify the partition table >>>>>> w write table to disk and exit >>>>>> x extra functionality (experts only) >>>>>> >>>>>> Command (m for help): q >>>>>> >>>>>> sudo fdisk -l /dev/sdd1 >>>>>> >>>>>> Disk /dev/sdd1: 2001 MB, 2001731584 bytes >>>>>> 62 heads, 62 sectors/track, 1017 cylinders, total 3909632 sectors >>>>>> Units = sectors of 1 * 512 = 512 bytes >>>>>> Sector size (logical/physical): 512 bytes / 512 bytes >>>>>> I/O size (minimum/optimal): 512 bytes / 512 bytes >>>>>> Disk identifier: 0x20ac7dda >>>>>> >>>>>> This doesn't look like a partition table >>>>>> Probably you selected the wrong device. >>>>>> >>>>>> Device Boot Start End Blocks Id System >>>>>> /dev/sdd1p1 ? 3224498923 3657370039 216435558+ 7 >>>>>> HPFS/NTFS/exFAT >>>>>> /dev/sdd1p2 ? 3272020941 930513678 976730017 16 Hidden FAT16 >>>>>> /dev/sdd1p3 ? 0 0 0 6f Unknown >>>>>> /dev/sdd1p4 50200576 974536369 462167897 0 Empty >>>>>> >>>>>> Partition table entries are not in disk order >>>>>> >>>>>> ****Now when I plug the USB drive in and it automounts nothing new >>>>>> appears in the file manager. SO I ran another program to see what it says: >>>>>> >>>>>> bmike1@PresarioLapTop1:/media/bmike1/OpenELEC$ sudo sfdisk /dev/sdd >>>>>> Checking that no-one is using this disk right now ... >>>>>> OK >>>>>> >>>>>> Disk /dev/sdd: 1018 cylinders, 62 heads, 62 sectors/track >>>>>> Old situation: >>>>>> Warning: The partition table looks like it was made >>>>>> for C/H/S=*/11/4 (instead of 1018/62/62). >>>>>> For this listing I'll assume that geometry. >>>>>> Units = cylinders of 22528 bytes, blocks of 1024 bytes, counting from >>>>>> 0 >>>>>> >>>>>> Device Boot Start End #cyls #blocks Id System >>>>>> /dev/sdd1 46+ 88946- 88901- 1955808 83 Linux >>>>>> start: (c,h,s) expected (46,6,1) found (1,78,9) >>>>>> end: (c,h,s) expected (1023,10,4) found (34,10,4) >>>>>> /dev/sdd2 0 - 0 0 0 Empty >>>>>> /dev/sdd3 0 - 0 0 0 Empty >>>>>> /dev/sdd4 0 - 0 0 0 Empty >>>>>> Input in the following format; absent fields get a default value. >>>>>> >>>>>> Usually you only need to specify and (and perhaps >>>>>> ). >>>>>> >>>>>> /dev/sdd1 :? >>>>>> trailing junk after number >>>>>> >>>>>> /dev/sdd1 : >>>>>> >>>>>> >>>>>> :-)~MIKE~(-: >>>>>> >>>>>> >>>>>> On Tue, May 6, 2014 at 7:29 AM, Mike Ballon wrote: >>>>>> >>>>>>> First I was wrong to say that /dev/sdd1 would not exist it you >>>>>>> simply unmounted it. I believe it can vary between a physical system and a >>>>>>> VM. >>>>>>> >>>>>>> -- returns the memory stick i just plugged in and assigns device >>>>>>> /dev/sdb >>>>>>> >>>>>>> $> dmesg >>>>>>> >>>>>>> [ 452.300827] scsi 3:0:0:0: Direct-Access Kingston DataTraveler >>>>>>> 2.0 PMAP PQ: 0 ANSI: 4 >>>>>>> [ 452.302226] sd 3:0:0:0: Attached scsi generic sg2 type 0 >>>>>>> [ 452.316528] sd 3:0:0:0: [sdb] 15240576 512-byte logical blocks: >>>>>>> (7.80 GB/7.26 >>>>>>> >>>>>>> -- automount presents the stick to me because it has a file system >>>>>>> >>>>>>> $> mount | grep sdb >>>>>>> >>>>>>> /dev/sdb1 on /media/UNTITLED type vfat >>>>>>> >>>>>>> -- fdisk returns the partition info >>>>>>> >>>>>>> $> fdisk -l /dev/sdb >>>>>>> >>>>>>> Device Boot Start End Blocks Id System >>>>>>> /dev/sdb1 2 15240575 7620287 b W95 FAT32 >>>>>>> >>>>>>> -- use fdisk to delete the partition >>>>>>> >>>>>>> $> fdisk /dev/sdb >>>>>>> $> Command > d >>>>>>> $> Command > w >>>>>>> $> Command > p >>>>>>> >>>>>>> Device Boot Start End Blocks Id System >>>>>>> >>>>>>> -- use fdisk to create the partition >>>>>>> >>>>>>> $> fdisk /dev/sdb >>>>>>> $> Command > o >>>>>>> $> Command > n >>>>>>> $> Command > 1 (press enter 3times) >>>>>>> $> Command > t >>>>>>> $> Command > b >>>>>>> $> Command > w >>>>>>> $> Command > p >>>>>>> >>>>>>> Device Boot Start End Blocks Id System >>>>>>> /dev/sdb1 2048 15240575 7619264 b W95 FAT32 >>>>>>> >>>>>>> -- make the file system if needed, I say if needed because since the >>>>>>> partition is exactly the same and the fs is the same, automount mounted the >>>>>>> stick for me automagically >>>>>>> >>>>>>> $> umount /dev/sdb1 >>>>>>> $> mkfs.vfat /dev/sdb1 >>>>>>> $> mount /dev/sdb /mnt/foobar >>>>>>> $> touch /mnt/foobar/test.txt >>>>>>> $> ls /mnt/fobar >>>>>>> >>>>>>> test.txt >>>>>>> >>>>>>> -- oops forgot the renaming of volume, I'm on debian so >>>>>>> >>>>>>> $> apt-get install mtools >>>>>>> >>>>>>> Setting up mtools (4.0.17-1) ... >>>>>>> >>>>>>> $> mlabel -i /dev/sdb1 ::usb_stick >>>>>>> >>>>>>> again... gparted is your friend >>>>>>> >>>>>>> >>>>>>> On Tue, May 6, 2014 at 9:42 AM, Mike Ballon wrote: >>>>>>> >>>>>>>> if you unmounted then /dev/sdd1 would no longer be there. >>>>>>>> >>>>>>>> Give me a few mins and I'll spin up a VM (I'm on a Mac) and I'll >>>>>>>> run through all the steps for you. >>>>>>>> >>>>>>>> >>>>>>>> On Tue, May 6, 2014 at 3:34 AM, Michael Havens wrote: >>>>>>>> >>>>>>>>> bummer.... new drive: >>>>>>>>> >>>>>>>>> mount >>>>>>>>> ... >>>>>>>>> /dev/sdd1 on /media/bmike1/OpenELEC type vfat >>>>>>>>> (rw,nosuid,nodev,uid=1000,gid=1000,shortname=mixed,dmask=0077,utf8=1,showexec,flush,uhelper=udisks2) >>>>>>>>> >>>>>>>>> bmike1@PresarioLapTop1:/media/bmike1/OpenELEC$ sudo mkfs -t vfat >>>>>>>>> /dev/sdd1 >>>>>>>>> mkfs.vfat 3.0.13 (30 Jun 2012) >>>>>>>>> /dev/sdd1: No such file or directory >>>>>>>>> bmike1@PresarioLapTop1:/media/bmike1/OpenELEC$ >>>>>>>>> bmike1@PresarioLapTop1:/media/bmike1/OpenELEC$ sudo mkfs -t vfat >>>>>>>>> /dev/sdd1 >>>>>>>>> mkfs.vfat 3.0.13 (30 Jun 2012) >>>>>>>>> /dev/sdd1: No such file or directory >>>>>>>>> bmike1@PresarioLapTop1:/media/bmike1/OpenELEC$ sudo e2label >>>>>>>>> /dev/sdd1 Pny2G >>>>>>>>> e2label: No such file or directory while trying to open /dev/sdd1 >>>>>>>>> Couldn't find valid filesystem superblock. >>>>>>>>> >>>>>>>>> what am I doing wrong? >>>>>>>>> >>>>>>>>> :-)~MIKE~(-: >>>>>>>>> >>>>>>>>> >>>>>>>>> On Mon, May 5, 2014 at 8:28 PM, Michael Havens wrote: >>>>>>>>> >>>>>>>>>> that wouldn't change a vfat system but it inspired the correct >>>>>>>>>> search terms and I found 'dosfslabel'. Thanks for the help, man:D >>>>>>>>>> >>>>>>>>>> :-)~MIKE~(-: >>>>>>>>>> >>>>>>>>>> >>>>>>>>>> On Mon, May 5, 2014 at 7:50 PM, Ryan Rix wrote: >>>>>>>>>> >>>>>>>>>>> Yeah, you're right Mike. >>>>>>>>>>> >>>>>>>>>>> https://help.ubuntu.com/community/RenameUSBDrive#FAT16_and_FAT32 >>>>>>>>>>> >>>>>>>>>>> Michael Havens writes: >>>>>>>>>>> > same thing: >>>>>>>>>>> > >>>>>>>>>>> > sudo e2label /dev/sdd1 Goodwill >>>>>>>>>>> > e2label: Bad magic number in super-block while trying to open >>>>>>>>>>> > /dev/sdd1 >>>>>>>>>>> > Couldn't find valid filesystem superblock. >>>>>>>>>>> > >>>>>>>>>>> > could it be because it is a vfat file system? (while I love >>>>>>>>>>> linux I >>>>>>>>>>> > like to have the ability for my flash drives to be used on >>>>>>>>>>> common >>>>>>>>>>> > computers) >>>>>>>>>>> > >>>>>>>>>>> > :-)~MIKE~(-: >>>>>>>>>>> > >>>>>>>>>>> > On Mon, May 5, 2014 at 5:51 PM, Mike Ballon < >>>>>>>>>>> mike.ballon@gmail.com> >>>>>>>>>>> > wrote: >>>>>>>>>>> > >>>>>>>>>>> > It's I file system label so yes, you'll need to format. If >>>>>>>>>>> there >>>>>>>>>>> > is no partition will have to create a partition before you >>>>>>>>>>> can do >>>>>>>>>>> > a mkfs gparted should do all that for you >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > On May 5, 2014 7:47 PM, "Michael Havens" >>>>>>>>>>> wrote: >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > Thanks Mike. Does this error mean I need to format the >>>>>>>>>>> drive? >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > sudo e2label /dev/sdc1 Goodwill >>>>>>>>>>> > e2label: Bad magic number in super-block while trying >>>>>>>>>>> to open >>>>>>>>>>> > /dev/sdc1 >>>>>>>>>>> > Couldn't find valid filesystem superblock. >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > This is what 'mount' shows sdc1 to be: >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > /dev/sdc1 on /media/bmike1/OpenELEC type vfat >>>>>>>>>>> > >>>>>>>>>>> (rw,nosuid,nodev,uid=1000,gid=1000,shortname=mixed,dmask=0077,utf8=1, >>>>>>>>>>> > showexec,flush,uhelper=udisks2) >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > and to format this and apply the label it would be: >>>>>>>>>>> > >>>>>>>>>>> > mkfs -t vfat /dev/sdc1;e2label /dev/sdc1 Goodwill >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > :-)~MIKE~(-: >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > On Mon, May 5, 2014 at 4:08 PM, Mike Ballon >>>>>>>>>>> > wrote: >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > e2label >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > On Mon, May 5, 2014 at 7:05 PM, Michael Havens >>>>>>>>>>> > wrote: >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > I have a few flash drives. When I plug them in >>>>>>>>>>> to my >>>>>>>>>>> > computer a name referring to that flash drive >>>>>>>>>>> appears >>>>>>>>>>> > in the file manager. I have two questions: the >>>>>>>>>>> first >>>>>>>>>>> > is how do I change that name? The second is >>>>>>>>>>> how do I >>>>>>>>>>> > set that name when I format the drive? >>>>>>>>>>> > >>>>>>>>>>> > :-)~MIKE~(-: >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> --------------------------------------------------- >>>>>>>>>>> > PLUG-discuss mailing list - >>>>>>>>>>> > PLUG-discuss@lists.phxlinux.org >>>>>>>>>>> > To subscribe, unsubscribe, or to change your >>>>>>>>>>> mail >>>>>>>>>>> > settings: >>>>>>>>>>> > >>>>>>>>>>> http://lists.phxlinux.org/mailman/listinfo/plug-discuss >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > --------------------------------------------------- >>>>>>>>>>> > PLUG-discuss mailing list - >>>>>>>>>>> > PLUG-discuss@lists.phxlinux.org >>>>>>>>>>> > To subscribe, unsubscribe, or to change your mail >>>>>>>>>>> > settings: >>>>>>>>>>> > >>>>>>>>>>> http://lists.phxlinux.org/mailman/listinfo/plug-discuss >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > --------------------------------------------------- >>>>>>>>>>> > PLUG-discuss mailing list - >>>>>>>>>>> PLUG-discuss@lists.phxlinux.org >>>>>>>>>>> > To subscribe, unsubscribe, or to change your mail >>>>>>>>>>> settings: >>>>>>>>>>> > >>>>>>>>>>> http://lists.phxlinux.org/mailman/listinfo/plug-discuss >>>>>>>>>>> > >>>>>>>>>>> > --------------------------------------------------- >>>>>>>>>>> > PLUG-discuss mailing list - >>>>>>>>>>> PLUG-discuss@lists.phxlinux.org >>>>>>>>>>> > To subscribe, unsubscribe, or to change your mail settings: >>>>>>>>>>> > http://lists.phxlinux.org/mailman/listinfo/plug-discuss >>>>>>>>>>> > >>>>>>>>>>> > >>>>>>>>>>> > --------------------------------------------------- >>>>>>>>>>> > PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org >>>>>>>>>>> > To subscribe, unsubscribe, or to change your mail settings: >>>>>>>>>>> > http://lists.phxlinux.org/mailman/listinfo/plug-discuss >>>>>>>>>>> --------------------------------------------------- >>>>>>>>>>> PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org >>>>>>>>>>> To subscribe, unsubscribe, or to change your mail settings: >>>>>>>>>>> http://lists.phxlinux.org/mailman/listinfo/plug-discuss >>>>>>>>>>> >>>>>>>>>> >>>>>>>>>> >>>>>>>>> >>>>>>>>> --------------------------------------------------- >>>>>>>>> PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org >>>>>>>>> To subscribe, unsubscribe, or to change your mail settings: >>>>>>>>> http://lists.phxlinux.org/mailman/listinfo/plug-discuss >>>>>>>>> >>>>>>>> >>>>>>>> >>>>>>> >>>>>>> --------------------------------------------------- >>>>>>> PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org >>>>>>> To subscribe, unsubscribe, or to change your mail settings: >>>>>>> http://lists.phxlinux.org/mailman/listinfo/plug-discuss >>>>>>> >>>>>> >>>>>> >>>>>> --------------------------------------------------- >>>>>> PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org >>>>>> To subscribe, unsubscribe, or to change your mail settings: >>>>>> http://lists.phxlinux.org/mailman/listinfo/plug-discuss >>>>>> >>>>> >>>>> >>>>> --------------------------------------------------- >>>>> PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org >>>>> To subscribe, unsubscribe, or to change your mail settings: >>>>> http://lists.phxlinux.org/mailman/listinfo/plug-discuss >>>>> >>>> >>>> >>> >>> --------------------------------------------------- >>> PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org >>> To subscribe, unsubscribe, or to change your mail settings: >>> http://lists.phxlinux.org/mailman/listinfo/plug-discuss >>> >> >> >> --------------------------------------------------- >> PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org >> To subscribe, unsubscribe, or to change your mail settings: >> http://lists.phxlinux.org/mailman/listinfo/plug-discuss >> > >