Nathan, Some of the old bricks are painfully cheap and fail. Sometimes it's just a capacitor but that usually means making a mess out of the brick just to get it working. Some routers require a lot of current (>1amp) which makes the smaller bricks fail. I've used this fix for both 12v and 5v routers. If you have a spare quiet or fan-less ATX power supply or don't mind the fan noise If you're handy with a soldering iron or gun, here's the messy solution I have employed in the past: (you'll want a VOM - volt-ohm meter or DVM) Just cut the cord off at the brick. Make sure there is continuity (i.e. a connection) between each bare wire from the brick end and the plug terminal on the other end. Make sure the two bare wires and the plug are not shorted. Take an old ATX power supply and splice the plug into the 12 volt side (yellow and black) of one of the molex connectors - those are the (usually) white four-wire ones. (The other wire with black, which is common and negative in polarity) Make sure the polarity (+,-) is the same as noted on the brick. On the main ATX power connector, short the green wire to a black wire (use a piece of bare copper wire and secure with a short piece of duct tape). It's a primitive solution, if not temporary, but you probably won't see another power failure with this fix. This fix is only good for 12 or 5 (red wire) volt power requirements. Alternate fix is to find a good 1+amp 12volt brick and splice the old cord into it. Jon/coverturtle tsu.co/coverturtle On 12/02/2014 02:20 AM, Nathan England wrote: > > Hey, that's a really good idea! I was at a GoodWill a few weeks ago and > saw several of them. I even jokingly made the comment out about the > power bricks... > > Oh well... > > > On 2014-12-01 23:40, David Schwartz wrote: >> Check your nearest GoodWill Store. >> >> They always seem to have lots of older routers, although they separate >> the wallwarts from them for whatever stupid reason. >> >> -David >> >> >> >>> On Dec 1, 2014, at 10:37 PM, Nathan England wrote: >>> >>> >>> Hey all, >>> >>> The power brick for my Linksys E2000 died. I bought a new Linksys and >>> used the old power cord and the new linksys failed to power up like >>> the old linksys. So I tried the power brick from the new linksys and >>> it works on both routers perfectly... >>> >>> So, I'm looking to find a 1.0amp 12v power brick for a linksys or >>> similar that will work. I don't want to spend the money to buy a >>> variable power brick, they're not cheap and I am... ha ha >>> >>> Has anyone got a dead linksys I can come and pick up? I'm in the west >>> valley but might be willing to drive a ways if you have one! >>> >>> I appreciate your help! >>> >>> >>> -- >>> Regards, >>> Nathan England >>> >>> (480) 559-9681 >>> >>> --------------------------------------------------- >>> PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org >>> To subscribe, unsubscribe, or to change your mail settings: >>> http://lists.phxlinux.org/mailman/listinfo/plug-discuss > > Hey, that's a really good idea! I was at a GoodWill a few weeks ago and saw several of them. I even jokingly made the comment out about the power bricks... Oh well... On 2014-12-01 23:40, David Schwartz wrote: > Check your nearest GoodWill Store. > > They always seem to have lots of older routers, although they separate > the wallwarts from them for whatever stupid reason. > > -David > > > >> On Dec 1, 2014, at 10:37 PM, Nathan England wrote: >> >> >> Hey all, >> >> The power brick for my Linksys E2000 died. I bought a new Linksys and >> used the old power cord and the new linksys failed to power up like >> the old linksys. So I tried the power brick from the new linksys and >> it works on both routers perfectly... >> >> So, I'm looking to find a 1.0amp 12v power brick for a linksys or >> similar that will work. I don't want to spend the money to buy a >> variable power brick, they're not cheap and I am... ha ha >> >> Has anyone got a dead linksys I can come and pick up? I'm in the west >> valley but might be willing to drive a ways if you have one! >> >> I appreciate your help! >> >> >> -- >> Regards, >> Nathan England >> >> (480) 559-9681 >> >> --------------------------------------------------- >> PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org >> To subscribe, unsubscribe, or to change your mail settings: >> http://lists.phxlinux.org/mailman/listinfo/plug-discuss -- Regards, Nathan England ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ NME Consulting Services http://www.nmecs.com Nathan England ( nathan@nmecs.com ) Systems Administration / Web Application Development Information Security Consulting (480) 559.9681 --------------------------------------------------- PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org To subscribe, unsubscribe, or to change your mail settings: http://lists.phxlinux.org/mailman/listinfo/plug-discuss --------------------------------------------------- PLUG-discuss mailing list - PLUG-discuss@lists.phxlinux.org To subscribe, unsubscribe, or to change your mail settings: http://lists.phxlinux.org/mailman/listinfo/plug-discuss