In your first email you said eth0 is connected to the Internet. However, it seems that eth0 has the IP address 10.100.1.102. Is that a private network behind a machine doing NAT? That being the case, is its private address 10.100.1.245? Can this machine ping that IP? Can any machine on this private network get out? (As in, is the NAT box working properly.) On 4/15/05, Jesus E Zepeda wrote: > Hi, Craig: > > I tried setting the Gateway to eth0 with no positive result. Eventhough > both are on the same machine the subnet is different. > > As far as acting as a router, the /proc/sys/net/ipv4/ip_forward is equal > 1 > > These are the outputs you instructed: > > Thanks. Jesus... > ----- > route -n > > [root@custom1 root]# route -n > Kernel IP routing table > Destination Gateway Genmask Flags Metric Ref Use > Iface > 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 > eth1 > 10.100.0.0 0.0.0.0 255.255.0.0 U 0 0 0 > eth0 > 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 > eth0 > 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 > lo > 0.0.0.0 10.100.1.245 0.0.0.0 UG 0 0 0 > eth0 > [root@custom1 root]# > > ----- > [root@custom1 root]# ifconfig -a > eth0 Link encap:Ethernet HWaddr 00:A0:CC:D9:7D:E0 > inet addr:10.100.1.102 Bcast:10.100.255.255 Mask:255.255.0.0 > inet6 addr: fe80::2a0:ccff:fed9:7de0/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:234 errors:1 dropped:0 overruns:0 frame:0 > TX packets:321 errors:523 dropped:0 overruns:0 carrier:1042 > collisions:0 txqueuelen:1000 > RX bytes:23727 (23.1 Kb) TX bytes:36623 (35.7 Kb) > Interrupt:9 Base address:0x1400 > > eth1 Link encap:Ethernet HWaddr 00:50:04:D8:79:A3 > inet addr:192.168.1.204 Bcast:192.168.1.255 > Mask:255.255.255.0 > inet6 addr: fe80::250:4ff:fed8:79a3/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:4712 errors:0 dropped:0 overruns:1 frame:0 > TX packets:3718 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:648107 (632.9 Kb) TX bytes:739930 (722.5 Kb) > Interrupt:11 Base address:0x1800 > > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > inet6 addr: ::1/128 Scope:Host > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:5402 errors:0 dropped:0 overruns:0 frame:0 > TX packets:5402 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:2746643 (2.6 Mb) TX bytes:2746643 (2.6 Mb) > > sit0 Link encap:IPv6-in-IPv4 > NOARP MTU:1480 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) > > ------ > cat /etc/sysconfig/network-scripts/ifcfg-eth0 > > [# Please read /usr/share/doc/initscripts-*/sysconfig.txt > # for the documentation of these parameters. > IPV6INIT=no > ONBOOT=yes > USERCTL=no > PEERDNS=yes > GATEWAY=10.100.1.245 > TYPE=Ethernet > DEVICE=eth0 > HWADDR=00:a0:cc:d9:7d:e0 > BOOTPROTO=none > NETMASK=255.255.0.0 > IPADDR=10.100.1.102 > > ---------- > cat /etc/sysconfig/network-scripts/ifcfg-eth1 > > # Please read /usr/share/doc/initscripts-*/sysconfig.txt > # for the documentation of these parameters. > IPV6INIT=no > ONBOOT=yes > USERCTL=no > PEERDNS=yes > GATEWAY=10.100.1.102 > TYPE=Ethernet > DEVICE=eth1 > HWADDR=00:50:04:d8:79:a3 > BOOTPROTO=none > NETMASK=255.255.255.0 > IPADDR=192.168.1.204 > > ----- > cat /etc/sysconfig/network > > NETWORKING=yes > HOSTNAME=custom1 > > -----Original Message----- > From: Craig White [mailto:craigwhite@azapple.com] > Sent: Friday, April 15, 2005 10:55 > To: plug-discuss@lists.plug.phoenix.az.us > Subject: Re: Eth1 and eth0 > > On Fri, 2005-04-15 at 10:34 -0700, Jesus E Zepeda wrote: > > Hello, list: > > > > I am using Fedora Core 2 in my computer, which is setup with two NICs: > > > Eth1 NIC is connected to the LAN; and eth0 connected to the Internet. > > Also, eth1 NIC has as a gateway an interface of a router. > > > > Both eth0 and eth1 are active. I can ping from one another interface > > and to any host on either side. The problem I have is that I cannot > > reach the other side of the router. > > > > What can I do to be able to have my computer talk to both sides and > > across the router, when I know that the router will reply on the other > > > side if I have eth0 (Internet) removed? > ---- > seems to me that the gateway device should be eth0. > > it would be easier if you gave us the output of... > > route -n > > ifconfig -a > > cat /etc/sysconfig/network-scripts/ifcfg-eth0 > > cat /etc/sysconfig/network-scripts/ifcfg-eth1 > > cat /etc/sysconfig/network > > also, to act as a router, your probably need to do some things like... > echo "1" > /proc/sys/net/ipv4/ip_forward > > suggest that you look at... > http://www.ecst.csuchico.edu/~dranch/LINUX/ipmasq/c-html/stronger- > firewall-examples.html#RC.FIREWALL-2.4.X-STRONGER > > Craig > > --------------------------------------------------- > PLUG-discuss mailing list - PLUG-discuss@lists.plug.phoenix.az.us > To subscribe, unsubscribe, or to change you mail settings: > http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss > > --------------------------------------------------- > PLUG-discuss mailing list - PLUG-discuss@lists.plug.phoenix.az.us > To subscribe, unsubscribe, or to change you mail settings: > http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss > --------------------------------------------------- PLUG-discuss mailing list - PLUG-discuss@lists.plug.phoenix.az.us To subscribe, unsubscribe, or to change you mail settings: http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss