I concur that the problem is that there's no gateway defined in the 
routing table. From what I know, Kevin's suggestion should have fixed it 
in a distro-independent fashion. I'm not familiar with how SuSE has 
networking configuration set up "under the hood". At this point, I'd try 
to use YaST to delete eth1, save your settings (maybe even reboot), add 
eth1 back using YaST, save settings, restart networking, then check the 
routing table again. If the gateway entry isn't there, add it using the 
route command, and it should work. Once it's working, you'll need to 
find out where/why SuSE/YaST is (apparently) not getting it quite right.

P.S. The problem might also be that DHCP w/ wireless isn't working 
entirely correct (gateway portion might be broken?). I'd try doing a 
static configuration and see if that works.

Michael Sammartano wrote:
> I just tried this and then # rcnetwork restart
> This did not work so I am trying a reboot (old school windows, sorry), 
> as I have noticed sometimes this works as I forget the command to 
> re-read a config file..
> I am getting an error at boot..
>  Setting up network 
> service.......................................................FAILED
> KevinO wrote:
> 
>> -----BEGIN PGP SIGNED MESSAGE-----
>> Hash: SHA1
>>
>> Kevin Brown wrote:
>>  
>>
>>>> LINUX:~ # route -n
>>>> Kernel IP routing table
>>>> Destination     Gateway         Genmask         Flags Metric Ref   
>>>> Use Iface
>>>> 192.168.0.0     0.0.0.0         255.255.255.0   U     0      0       
>>>> 0 eth1
>>>> 169.254.0.0     0.0.0.0         255.255.0.0     U     0      0       
>>>> 0 eth1
>>>> 127.0.0.0       0.0.0.0         255.0.0.0       U     0      0       
>>>> 0 lo
>>>>     
>>>
>>> And we have a winner.  There is no Gateway address in your route 
>>> list. I can tell because none of the routes you have are flagged as 
>>> UG, just
>>> U.  This means you need to add a default route of the following:
>>>
>>> Destination 0.0.0.0
>>> Gateway 192.168.0.1
>>> Genmask 0.0.0.0
>>>
>>> This can be done with the route command (don't recall the syntax).  Not
>>> sure why dhcp isn't doing it for you when it gets your IP address from
>>> the router though.
>>>
>>>   
>>
>> # route add default gw 192.168.0.1 eth1
>>
>>
>> - --
>> KevinO
>> -----BEGIN PGP SIGNATURE-----
>> Version: GnuPG v1.2.4 (GNU/Linux)
>> Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org
>>
>> iD8DBQFCSkgEI3MJ/OwKti0RAqGOAJ42C287qz1nr4bthtKLQ9xXXvLfawCeOCdJ
>> Q2NYjyO2FiI7nZNtt+Oq2TY=
>> =R+cX
>> -----END PGP SIGNATURE-----
>> ---------------------------------------------------
>> PLUG-discuss mailing list - PLUG-discuss@lists.plug.phoenix.az.us
>> To subscribe, unsubscribe, or to change  you mail settings:
>> http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss
>>
>>  
>>
> 


-- 
-Eric 'shubes'
"There is no such thing as the People;
  it is a collectivist myth.
  There are only individual citizens
  with individual wills
  and individual purposes."
-William E. Simon (1927-2000),
     Secretary of the Treasury (1974-1977)
  "A Time For Truth" (1978), pg. 237

 
---------------------------------------------------
PLUG-discuss mailing list - PLUG-discuss@lists.plug.phoenix.az.us
To subscribe, unsubscribe, or to change  you mail settings:
http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss