Am 23. Jun, 2000 schwäzte Mike Starke so: > I have a bunch of html documents that I would like to convert > to either postscript (prefered) or pdf format. No problem > there, I am just using 'html2ps'. The problem I am having > is getting images into my postscrpt documents. > > I have tried using .ps, .png, .jpg, and .bmp as the images > in the html documents, but no luck. eps is what should work, if I remember right. It'll be mentioned somewhere in the HOWTO-HOWTO at the LDP, www.LinuxDoc.org. ciao, der.hans -- # der.hans@LuftHans.com home.pages.de/~lufthans/ www.Opnix.com # If you're not learning, you're not living. - der.hans From " linuxnet"@home.com Sat Jun 24 03:02:50 2000 From: " linuxnet"@home.com (anselrodriguez) Date: Fri, 23 Jun 2000 20:02:50 -0700 Subject: Turning off video power management in X on Mandrake v7.1 References: <000a01bfdd2b$72d5a700$0201a8c0@home.cxm> Message-ID: <395424DA.992EE4A1@home.com> --------------61784AAA4973418734AD6954 Content-Type: text/plain; charset=us-ascii Content-Transfer-Encoding: 7bit Donn, it sounds like it could be the power saving mode of kcmdpms. Donn Shumway wrote: > I recently installed Mandrake v7.1 on a K6II-450, 128Mb RAM, Voodoo3-2000. I > had a few strange occurances during install, but now everything (almost) > seems to be working fine. > > The problem is that a few minutes after the screen saver comes on (using > KDE), my monitor goes into a non-sync mode that I assume is some power > saving feature of the video system. I have not experienced this with > previous versions of Mandrake. I checked the BIOS during boot and APM > features are turned off. Is there a setting in the XF86Config file that I > can change to eliminate this problem? > > Also, the install seems to recognize my Voodoo3-2000 as a 'Voodoo 3 > (Generic). Is this normal for XFree86 v3.3.6? > > I looked in the XF86Config file and there is a line in the 'Graphics Device > Section' that reads: > > ------------------------ > Section "Device" > Identifier "Generic VGA" > Chipset "generic" > EndSection > > Section "Device" > Identifier "Voodoo3 (generic)" > VendorName "Unknown" > Boardname "Unknown" > * VideoRam 16384 > * Clock lines > > * Uncomment following option if you see a big white block > * instead of the cursor! > *Option "sw_cursor" > > Option "power_saver" > EndSection > ------------------------ > > If I comment out the Option "power_saver" will this disable the option? > > Thanks for all your assistance. > The Reiser FS is really impressive! > > Regards, > Donn Shumway > > _______________________________________________ > Plug-discuss mailing list - Plug-discuss@lists.PLUG.phoenix.az.us > http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss -- /////////////////////////////////////////////////////////////////////////////// a true monopoly is always goverment run, in the private sector we will always find a better way to do the things others want to control. \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\ --------------61784AAA4973418734AD6954 Content-Type: text/html; charset=us-ascii Content-Transfer-Encoding: 7bit Donn, it sounds like it could be the power saving mode of kcmdpms.
 

Donn Shumway wrote:

I recently installed Mandrake v7.1 on a K6II-450, 128Mb RAM, Voodoo3-2000. I
had a few strange occurances during install, but now everything (almost)
seems to be working fine.

The problem is that a few minutes after the screen saver comes on (using
KDE), my monitor goes into a non-sync mode that I assume is some power
saving feature of the video system. I have not experienced this with
previous versions of Mandrake. I checked the BIOS during boot and APM
features are turned off. Is there a setting in the XF86Config file that I
can change to eliminate this problem?

Also, the install seems to recognize my Voodoo3-2000 as a 'Voodoo 3
(Generic). Is this normal for XFree86 v3.3.6?

I looked in the XF86Config file and there is a line in the 'Graphics Device
Section' that reads:

------------------------
Section "Device"
    Identifier "Generic VGA"
    Chipset "generic"
EndSection

Section "Device"
    Identifier "Voodoo3 (generic)"
    VendorName "Unknown"
    Boardname "Unknown"
*    VideoRam    16384
    * Clock lines

    * Uncomment following option if you see a big white block
    * instead of the cursor!
    *Option    "sw_cursor"

    Option "power_saver"
EndSection
------------------------

If I comment out the Option "power_saver" will this disable the option?

Thanks for all your assistance.
The Reiser FS is really impressive!

Regards,
Donn Shumway

_______________________________________________
Plug-discuss mailing list  -  Plug-discuss@lists.PLUG.phoenix.az.us
http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss

-- 
///////////////////////////////////////////////////////////////////////////////
a true monopoly is always goverment run, in the private sector we will
always find a better way to do the things others want to control.
\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\
  --------------61784AAA4973418734AD6954--