This message is in MIME format. Since your mail reader does not understand
this format, some or all of this message may not be legible.

------_=_NextPart_000_01BFD001.F7D38F08
Content-Type: text/plain;
	charset="windows-1252"

I should also probably mention the fact that I use a boot floppy and I don't
boot from the hard disk...?

---------------------------------------
boot=/dev/hda
map=/boot/map
install=/boot/boot.b
prompt
timeout=50
default=linux-2216-7ide
append="hdc=ide-scsi"

image=/boot/vmlinuz-2.2.16ide-7
        label=linux-2216-7ide
	read-only
	root=/dev/hda1

image=/boot/vmlinuz-2.2.13-18abitsmp
	label=linux
	initrd=/boot/initrd-2.2.13-18abitsmp.img
	read-only
	root=/dev/hda1

image=/boot/vmlinuz-2.2.13-18abit
	label=linux-up
	initrd=/boot/initrd-2.2.13-18abit.img
	read-only
	root=/dev/hda1

--------------------------------
> -----Original Message-----
> From: Marc Chung [mailto:mchung@asu.edu]
> Sent: Tuesday, June 06, 2000 2:56 PM
> To: 'plug-discuss@lists.PLUG.phoenix.az.us'
> Subject: RE: CD-R and where I'm at now
> 
> 
> Lucas,
> 
>   Please post your lilo.conf file..
> 
> also, I didn't need to use modules.conf (or for some odd reason,
> conf.modules on rh6.2stock)
> 
> 
> 
> danke
> 
> -- 
> Marc Chung [mchung@asu.edu]
> "I went to the woods because I wanted to live deliberately"
> 
> 
> On Tue, 6 Jun 2000, Lucas Vogel wrote:
> 
> > That was some of the setup of the .config as a response to 
> Art, who showed
> > me what his looked like, for comparison purposes. It wasn't 
> just the whole
> > file either, only relative chunks. I listed my lsmod output 
> in there too,
> > and the other files were attached so that those that have 
> been helping would
> > know what my configuration looks right at the moment, so 
> they wouldn't have
> > to ask. Nothing in the .config section is anything that I 
> personally did to
> > the kernel, only what is sitting in the directory. 
> > 
> > I did add the "append" line to lilo.conf, and I also have 
> the "ignore" line
> > in modules.conf(up in the top) that the HOWTO talks about.
> > 
> > Maybe I should go thursday...
> > 
> > > -----Original Message-----
> > > From: Rod Roark [mailto:rod@sunsetsystems.com]
> > > Sent: Tuesday, June 06, 2000 2:16 PM
> > > To: plug-discuss@lists.PLUG.phoenix.az.us
> > > Subject: Re: CD-R and where I'm at now
> > > 
> > > 
> > > Then why did you give us your "make config" output?  Also is
> > > append="hd?=ide-scsi" in lilo.conf?  Did you rerun lilo after 
> > > putting it
> > > there?
> > > 
> > > If all else fails, perhaps you should bring the machine to a PLUG
> > > meeting.
> > > 
> > > -- Rod
> > > 
> > > Lucas Vogel wrote:
> > > > 
> > > > Unfortunately, I'm using this HOWTO as well as a stock kernel.
> > > > 
> > > > > -----Original Message-----
> > > > > From: Rod Roark [mailto:rod@sunsetsystems.com]
> > > > > Sent: Tuesday, June 06, 2000 1:53 PM
> > > > > To: plug-discuss@lists.PLUG.phoenix.az.us
> > > > > Subject: Re: CD-R and where I'm at now
> > > > >
> > > > >
> > > > > The following HOWTO pretty much covers it all.  If 
> you've already
> > > > > followed it carefully, perhaps something is wrong with your
> > > > > kernel build
> > > > > procedure and you should try a stock kernel.
> > > > >
> > > > >   http://www.linuxdoc.org/HOWTO/CD-Writing-HOWTO.html
> > > > >
> > > > > -- Rod
> > > 
> > > _______________________________________________
> > > Plug-discuss mailing list  -  
> Plug-discuss@lists.PLUG.phoenix.az.us
> > > http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss
> > > 
> > 
> > _______________________________________________
> > Plug-discuss mailing list  -  Plug-discuss@lists.PLUG.phoenix.az.us
> > http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss
> > 
> 
> 
> _______________________________________________
> Plug-discuss mailing list  -  Plug-discuss@lists.PLUG.phoenix.az.us
> http://lists.PLUG.phoenix.az.us/mailman/listinfo/plug-discuss
> 


------_=_NextPart_000_01BFD001.F7D38F08
Content-Type: text/plain;
	name="lilo.txt"
Content-Transfer-Encoding: quoted-printable
Content-Disposition: attachment;
	filename="lilo.txt"

# LILO Konfigurations-Datei=0A=
# Start LILO global Section=0A=
# If you want to prevent console users to boot with =
init=3D/bin/bash,=0A=
#  restrict usage of boot params by setting a passwd and using the =
option=0A=
#  restricted.=0A=
#passwd=3Dbootpwd=0A=
#restricted=0A=
initrd=3D/boot/initrd=0A=
append=3D"hdc=3Dide-scsi"=0A=
boot=3D/dev/fd0=0A=
#compact       # faster, but won't work on all systems.=0A=
vga=3Dnormal=0A=
read-only=0A=
prompt=0A=
timeout=3D100=0A=
# End LILO global Section=0A=
#=0A=
other =3D /dev/hda1=0A=
  label =3D dos=0A=
  table =3D /dev/hda=0A=
=0A=
#=0A=
image =3D /boot/vmlinuz=0A=
  root =3D /dev/hdb6=0A=
  label =3D suse=0A=
=0A=
=0A=

------_=_NextPart_000_01BFD001.F7D38F08--