Need help configuring my network

[Gilbert T. Gutierrez, Jr.]

---------- Response Is At Bottom --------------

Some sample command uutput:

stingray:/home/mark# iwconfig
lo        no wireless extensions.

ath0      IEEE 802.11  ESSID:"PMI"
          Mode:Managed  Frequency:2.427 GHz  Access Point: 00:12:17:0A:57:85
          Bit Rate:1 Mb/s   Tx-Power:18 dBm   Sensitivity=0/3
          Retry:off   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality=0/94  Signal level=-95 dBm  Noise level=-95 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

eth0      no wireless extensions.

sit0      no wireless extensions.
-------------------------------------------------------------------
stingray:/home/mark# ifconfig
ath0      Link encap:Ethernet  HWaddr 00:13:46:E3:68:2B
          inet addr:192.168.25.125  Bcast:192.168.25.255  Mask:255.255.255.0
          inet6 addr: fe80::213:46ff:fee3:682b/64 Scope:Link
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:1172 errors:7435 dropped:0 overruns:0 frame:7435
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:200
          RX bytes:73606 (71.8 KiB)  TX bytes:0 (0.0 b)
          Interrupt:169 Memory:e08b1000-e08c1000

eth0      Link encap:Ethernet  HWaddr 00:08:74:CC:3C:17
          inet6 addr: fe80::208:74ff:fecc:3c17/64 Scope:Link
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Base address:0xdcc0 Memory:ff6c0000-ff6e0000

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:1653 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1653 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:144614 (141.2 KiB)  TX bytes:144614 (141.2 KiB)

--------------------------------------------------------------------------
stingray:/home/mark# route -n
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use
Iface
192.168.25.0    0.0.0.0         255.255.255.0   U     0      0        0 ath0
127.0.0.0       0.0.0.0         255.0.0.0       U     0      0        0 lo
0.0.0.0         192.168.25.1    0.0.0.0         UG    0      0        0 ath0
stingray:/home/mark#
----------------------------------------------------------------------------
--------

/etc/network/interfaces

# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

# The loopback network interface
auto lo
iface lo inet loopback

# The primary network interface
#auto eth0
#iface eth0 inet dhcp
allow-hotplug eth0
iface eth0 inet static
	address 192.168.25.125
        netmask 255.255.255.0
	broadcast 192.168.25.255
	gateway 192.168.25.1

# The wireless network interface
allow-hotplug ath0
iface ath0 inet static
	wpa-driver madwifi
	wpa-ssid PMI
	address 192.168.25.125
	netmask 255.255.255.0
	broadcast 192.168.25.255
	gateway 192.168.25.1


---------- Response --------------

Have you checked you firewall to make sure you are not blocking?  Also, are
both interfaces active at the same time?  I see that both adapters have the
same static IP address (Not a good idea in my mind).  I am assuming that if
you shut down the wireless connection and enable the wired connection you
can get out.  If you only have the wireless adapter enabled and the wired
adapter disabled, can you ping yourself?

Gilbert

---
[ This E-mail was scanned for viruses by Phoenix Internet ]
[ Phoenix Internet http://www.phoenixinternet.net ]